Additional Operating Instructions
CW301300AJ, CW301400AJ
Instrucciones Adicionales
CW301300AJ, CW301400AJ
New Switch Installation (Continued)
in kit. Insert motor and line cord into switch. Tighten strain relief clamp screw to hold cords securely.
8.Position black motor wire underneath screw head #4 (See Fig. 4), then tighten screw to secure wire. Position black line wire underneath screw head #3, then tighten screw to secure wire.
9.Position white line wire underneath screw head #1, then tighten screw to secure wire. Position white motor wire underneath screw head #2, then tighten screw to secure wire (See Fig. 4).
10.Attach green ground wire from line cord to inside of pressure switch with ground screw provided in kit. Repeat procedure with green ground wire from motor cord. (See Fig.4
IMPORTANT: Read
instructions before operating
compressor or damage may MANUAL result.
1.Turn switch to OFF position and plug in power cord (Fig. 6).
2.Turn switch to AUTO position to run unit (Fig. 6).
Instrucciones para operar (Continuación)
IMPORTANTE: Lea estas |
|
|
|
instrucciones antes de operar |
|
|
|
|
| ||
el compresor o podría dañarlo. |
| MANUAL |
|
|
|
| |
|
|
|
|
|
|
|
|
1. | Coloque el presostato en “off” y |
| conecte el cordón eléctrico al |
| tomacorrientes (Fig. 6). |
2. | Coloque el presostato en “auto” |
| para operar la unidad (Fig. 6). |
4.Conecte el extremo de la manguera a la perilla del regulador. Gire el regulador en sentido horario para aumentar la presión que sirve la herramienta que está usando.
AVISO Este
pre-
sostato debe estar en OFF cuando vaya a conectar o desconectar el cordón eléctrico del tomacorrientes
A | FF |
U | |
| TO / O |
Figura 6
1 | 2 |
LINE | MOTOR |
LINE | MTR |
3 | 4 |
Ground terminals | |
Figure 4
11.Place cover on pressure switch and tighten cover screw.
12.Screw regulator onto pressure switch.
NOTE: Ensure air flow indicator arrow on regulator body points away from compressor (See Fig. 5).
Hose
Outlet
Air Flow
Figure 5
13.Attach outlet pressure gauge to regulator.
Operating Procedure
In the AUTO position, the compressor pumps air into tank. It shuts off automatically when unit reaches its maximum preset pressure. In the OFF position, the pressure switch cannot function and the compressor will not operate.
A | FF |
U | |
| TO / O |
Figure 6
3.Turn regulator knob fully counterclockwise. Compressor will build to maximum preset pressure and shut off.
4.Attach end of hose to regulator knob. Turn regulator clockwise to increase pressure going to the tool that is being used.
|
| This switch should |
| NOTICE | |
| be in the OFF | |
|
|
position when connecting or
disconnecting the power cord from the electrical outlet.
3. Gire la perilla del regulador |
completamente en sentido contrario |
a las agujas del reloj. El compresor |
alcanzará la presión máxima fijada |
de fábrica y se apagará. |
Notas
Replacement Parts List - See Figure 2
Ref.
No.Description
1Bushing Reducer
2Strain Relief Clamp (ST/SJT) Strain Relief Clamp (SJT/SJT)
3ASME Safety Valve (140 psi) (CW301300AJ) ASME Safety Valve (115 psi) (CW301400AJ)
41/4" Nipple
5Pressure Gauge
6Unloader Valve
7Pressure Switch (CW301300AJ) Pressure Switch (CW301400AJ)
8Regulator
9Quick Connect
10Unloader Tube
11Clamp Screw
12Ground Screw
www.chpower.com
Part Number | Qty |
ST071407AV1
CW209500AV1
CW209600AV1
HF002401AV2
GA016302AV2
CW210000AV1
CW211200AJ1
CW213100AJ1
RE206203AV1
ST081301AV1
ST117803AV1
ST209800AV1
ST074407AV2
2 | 7 |