4FEATURES

AMPLIFIER MODE SWITCH

This switch enables you to slave multiple RS amplifiers off one master. Input signal will be connected to the master in a system, and then a PM2 bridging cable can be used to connect the master out to the slave in of a second amplifier, and in multiple amplifier systems, this amplifier’s master output can be connected to a third amplifier’s slave input, thus allowing the daisy chaining of an almost unlimited number of amplifiers from one signal source. In addition, a single Competition Podium Remote control (CPR) can optionally be connected to the master amplifier, in order to control all the slave amplifiers connected to it. Note that when an amplifier is set in the SLAVE mode, its level control, phase shift, subsonic filter, bass EQ, low pass filter, as well as remote control function will be totally bypassed, as these functions will be controlled by the master amplifier to ensure perfect level and spectral matching between all amplifiers.

“ARVA” - AUTOMATIC RAIL VOLTAGE ADJUSTMENT CIRCUITRY:

Cadence RS amplifiers feature "ARVA" circuitry in their power supply. This circuit constantly monitors the output stage and under high current demands will adjust the power supply rail voltages so that enough power is available for peak situations. The "ARVA" also improves the damping factor of the amplifier when playing low impedance mono loads. Cadence Type RS amplifiers have tighter sounding bass reproduction thanks to this unique circuitry.

BATTERY VOLTAGE:

Cadence RS amplifiers are rated and regulated to 13.8 volts and below. Increasing voltage to

14.4volts will increase the power output of the amplifier in the same proportion. Maximum input voltage is 16 volts while the minimum voltage is 12 volts.

Boom

Harder!

INDUCTION AND TUNNEL FAN COOLING:

Due to the extreme high power capabilities of these amplifiers, they feature a built-in induction fan cooling system. The amplifiers draw in cool air through the nosepiece side vents, for circulation across the circuitry. The main heatsink for the amplifier and power supply sections is a CAD designed forced cooled tunnel that runs the length of the amplifiers. A fan at each end, one pulling air in, and the other forcing air out, ensure that the power electronics stay cool for continued, clean operation. It is important not to block either the input or exhaust ports. Some of our competitors are more interested in making a quick buck and will purposely leave the fan out of their amps and then charge you a hefty sum to buy and add the fan on later. At Cadence, if we feel that our amplifiers will work better with a fan then we install it at the factory and don't make it an expensive add on option.

PROTECTION CIRCUITRY:

Cadence amplifiers incorporate many outstanding protection circuits to help protect the amplifier from being damaged during operating conditions.

Thermal Protection: When the amplifier reaches an unsafe operating temperature of 80 degrees Celsius the amplifier will turn off. Once the amplifier cools down, simply reset the amplifier by its Remote connection, (turn the amplifier off and then on again once you have given the amplifier a chance to cool down) and the amp will once again begin to play.

If you live in a hot climate we suggest installing additional cooling fans in your trunk to exhaust the hot air which can build up in the trunk this will help keep the ambient temperature in the trunk as low as possible so that your amps work flawlessly and without any musical interruption.

Speaker Short Circuit Protection: Should your speakers short circuit due to voice coil burn out, or should the amplifier sense an impedance too low to handle, the Protection LED will light, indicating a diagnostic condition. Turn off your system, disconnect one speaker at a time and try to determine which speaker might be faulty. Correct the condition and restart the amplifier. You must reset the amplifier by turning off and then on by the Remote power for proper operation after correcting a diagnostic condition.

Clipping or total shutdown may also be a result of a bad ground connection or loose ground. If you find that your speakers and speaker wires are not shorted, please check your ground connection.

Input Overload Protection: This circuit will either shutdown the amplifier completely or make the amplifier spurt on and off indicating that it is in a diagnostic condition. Turn the system off and reduce the gain on the amplifier or volume from your head unit, this should result in a corrected condition.

DC Offset Protection: Should any DC voltage try to enter the amplifier via the speaker terminals it will cause the amplifier to shut down and not operate until this condition is remedied. This circuit will also protect damaging high DC voltages from reaching your speakers should your amplifier ever miss-function.

MONO CLASS D specifications

Cadence Mono Class D amplifiers represent a significant advancement in audio amplification technology, designed to deliver high-quality sound while maintaining efficiency and compact size. These amplifiers are known for their ability to generate substantial power output with minimal heat generation, making them an ideal choice for various audio applications, from home theaters to professional sound systems.

One of the main features of the Cadence Mono Class D amps is their high power output capability. Utilizing a highly efficient switching power supply, these amplifiers can deliver substantial wattage to drive large speakers without distortion, providing a clean and powerful audio experience. This efficiency also translates into lower power consumption, making them environmentally friendly and cost-effective.

Another key technology integrated into Cadence Mono Class D amplifiers is pulse-width modulation (PWM). This technology enables precise control of the output signal, improving sound quality and reducing noise. The PWM technique allows for a more linear amplification process, resulting in better overall performance and fidelity. Users can expect clear highs, punchy mids, and deep, resonant bass that enhances the listening experience.

The robust construction of Cadence Mono Class D amplifiers is also noteworthy. Built with premium components and a durable chassis, these amplifiers are designed to withstand the rigors of both mobile and stationary use. Additionally, features such as built-in thermal protection and short circuit protection ensure longevity and reliability in various operating conditions.

Cadence Mono Class D amplifiers offer flexible connectivity options, including RCA and speaker-level inputs, making them compatible with a wide range of audio sources and systems. This versatility allows users to integrate the amplifier seamlessly into their existing setups without the need for complex configurations.

The compact form factor of these amplifiers makes them easy to install in tight spaces, a critical consideration for both car audio systems and home installations. Despite their small size, Cadence Mono Class D amplifiers deliver exceptional performance that rivals larger, more traditional amplifiers.

In summary, Cadence Mono Class D amplifiers combine advanced technologies, robust construction, and efficient design to provide powerful and high-quality audio amplification. With features such as high power output, PWM technology, flexible connectivity, and compact size, they are an excellent choice for audiophiles and casual listeners alike looking to elevate their sound experience.