VTX200 Three-Channel Guitar Amplifier with Stereo DSP
The Bottom Panel:
|
|
| SPEAKER OUTPUTS |
| STEREO |
|
| MONO | ||||||||||||||||||
| 100 WATTS @ 4 OHM MINIMUM LOAD | EFFECTS LOOP |
| EFFECTS LOOP | ||||||||||||||||||||||
| RIGHT |
|
| LEFT |
|
|
|
|
|
|
|
|
|
|
|
| FOOT | |||||||||
| (CHORUS DRY) |
|
| (CHORUS WET) | RETURN |
| SEND |
| RETURN |
|
|
| SWITCH | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SEND | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
29 |
|
| 30 | 31 | 32 | 33 | 34 | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
27:POWER (not shown): Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom) of the switch depressed. The switch illuminates when the power is on.
28:AC LINE CORD (not shown): This grounded power cord is to be plugged into a grounded power outlet, wired to current electrical codes and compatible with the voltage, power, and frequency requirements stated on the bot- tom panel. Do not attempt to defeat the safety ground connection.
29:SPEAKER OUTPUTS: Use these jacks to connect the amplifier to the speakers. The VTX200 is shipped from the factory with a cable from each channel connected to the speakers within the cabinet. Additional speakers may be connected providing the four ohm minimum load rating for these jacks is observed. When using the stereo Chorus effect the right channel is dry and the left channel is detuned (wet). Each channel will provide 70 watts RMS into an eight ohm load and 100 watts RMS into a four ohm load.
30:STEREO EFFECTS LOOP RETURN: When using a stereo external effects processor, connect this jack to the output jack of the effect by means of a shielded three conductor signal cable terminated with a stereo (R/T/S) 1/4” connector.
31:STEREO EFFECTS LOOP SEND: When using a stereo external effects processor, connect this jack to the input jack of the effect by means of a shielded three conductor signal cable terminated with a stereo (R/T/S) 1/4” connector.
32:MONO EFFECTS LOOP RETURN: When using a mono external effects processor, connect this jack to the output jack of the effect by means of a shielded signal cable.
33:MONO EFFECTS LOOP SEND: When using a mono external effects processor, connect this jack to the input jack of the effect by means of a shielded signal cable.
34:FOOTSWITCH: Use this jack to connect the footswitch cable
6