Coustic 161SE owner manual TROUBLE-SHOOTING Section, Symptom Probable Cause

Page 8

Figure 12: Input Sensitivity Control

1.Turn the Input Sensitivity Control all the way down (counter clockwise).

2.Set the volume control of the source unit to approximately 23 of its maximum output.

3.Turn the balance control of the source unit to its center position.

4.Leave the tone (bass/treble) controls at their usual position.

5.Play a CD or tape track with wide dynamic range

6.To locate the optimum input sensitivity setting, ask the person assisting you to turn the Input Sensitivity Control clockwise until audio distortion starts to develop. Turn the sensitivity control counter clockwise slightly to minimize the distortion.

7.If you constantly switch between CD/tape and radio, you will need further adjustment since radio output level differs from that of CD or tape. In this case, you need to locate a balanced sensitivity setting which is best for both the output level of radio and that of CD or tape.

 

 

COUSTIC.COM

 

 

 

 

TROUBLE-SHOOTING SECTION

SYMPTOM

PROBABLE CAUSE

1.

No power

Check connections to the amplifier's Ground, B+ & Remote termi-

 

 

nals. Check connection at "+" terminal of the battery. Check the

 

 

remote turn-on terminal. Ensure it receives power when the

 

 

source is turned on (or when the switch is turned on). Refer to the

 

 

Installation Section. Check the power line fuse: if fuse is blown,

 

 

replace it; if fuse continues to blow, check the power wire and

 

 

also the amplifier for a short. If the short is in the power wire, fix

 

 

it; if the short is in the amplifier itself, see your Coustic dealer.

 

 

Check the voltage at the amplifier, and the remote ON/OFF

 

 

lead. The voltage should measure between 11V-15V. If the meas-

 

 

urement is beyond this range, have the source unit checked out

 

 

by an authorized dealer.

2.

Power without sound with

Turn the amplifier off, and Check all input & output signal cables

 

red power/protection

and connections. Check the speakers for short with a VOM

 

indicator on

(volt meter) or by connecting them to another audio system. After

 

 

making sure everything is normal, turn the amplifier on again.

3.

Power without sound with

The continuous red light of the power indicator signals a high

 

red power indicator on

internal operating temperature, which results in the amplifier

 

 

switching off temporarily; when the amplifier cools down to a

 

 

safe level, the amp will automatically restart.

4.

No sound from one side

Check balance control.

 

 

Check speaker connections.

 

 

Check signal input connection.

5.

Very low sound from

Check your source unit's fader control.

 

both radio & tape

Check the amplifier's Input Sensitivity Level.

6.

Frequent automatic

This indicates that the amplifier is operating at a continually

 

amplifier shut down

undesirable high internal temperature. High operating tempera-

 

 

ture caused by inadequate ventilation: Refer to the sub-section

 

 

titled LOCATION for better amplifier location.

 

 

High operating temperature caused by an excessively low

 

 

impedance load, say below 2 ohms stereo or 4 ohms bridged:

 

 

Check for bad speakers and/or electronic crossover, proper pas-

sive crossover components; if all else fails, try rewiring the entire system.

High operating temperature can be caused by an incorrect input sensitivity level: refer to sub-section titled INPUT SENSITIVITY ADJUSTMENTS for correct setting.

7."Motorboating": The amplifier power indicator going off repeatedly when the audio system is on

8.Whining noise when engine is running with noise varying with the accelerator (noise level varies with source unit volume control).

Check the amplifier's connection to the battery. Check battery voltage. If low, recharge or replace battery.

Check all ground connections.

Reroute power cable from battery to source unit directly, bypassing the battery terminal in the fuse box. Check power connections to be sure they are clean. Check ground connections to be sure the ground wire is in direct contact with the bare metal surface of the chassis (with that spot scraped clean of all paint, rust or grease).

15

Image 8
Contents Coustic COUSTIC.COM Features WelcomeCONTROLS, INDICATORS, and Terminals Mounting InstallationLocation BI-AMPLIFICATION Typical System connectionFor Stereo Mode For Bridged Mono ModeInput Connections Speaker ConnectionsAdjustments TROUBLE-SHOOTING Section Symptom Probable CauseSpecifications SymptomBienvenu CaractéristiquesPanneau DES Entrées ET DES Configurations CONTRÕLES, Indicateurs ET ConnecteursEmplacement MontageInstallation traditionnelle BI AmplificationConnexion DU Signal Connexion DES Câbles HAUT-PARLEURSRéglages EN CAS DE Difficulté CousticCaractéristiques Techniques AttetionOPENED, Tampered with or Serial Numbers Removed Coustic Limited WarrantyImportant Notice to Consumer U 0 0 0 7 6 7 R e v B 1 / 0

161SE specifications

The Coustic 161SE is a cutting-edge audio amplifier designed for audiophiles and music enthusiasts seeking premium sound quality. With its sleek design and robust features, this amplifier encapsulates the essence of performance and modern technology.

One of the standout features of the Coustic 161SE is its power output. It delivers an impressive 1,600 watts of peak power, promising a dynamic audio experience. This allows users to drive even the most demanding speakers without sacrificing audio clarity. The amplifier is built on a Class AB design, which is known for producing less distortion and a more natural sound, making it suitable for both high and low-frequency audio playback.

The Coustic 161SE is also equipped with advanced signal processing technologies to enhance audio playback. It incorporates a low-noise design that minimizes interference and maximizes sound fidelity. With a frequency response range of 10Hz to 40kHz, the amplifier reproduces a wide spectrum of audio frequencies, ensuring that every note is captured with precision.

Moreover, the product features adjustable crossover settings, allowing users to tailor the sound to their personal preferences. This versatility makes it an ideal choice for various audio setups, whether used in a home theater system, a car audio system, or for professional audio installations.

User-friendly controls come standard with the Coustic 161SE. The front panel features simple adjustments for gain, bass boost, and high-pass/low-pass filters, providing intuitive access to key audio settings. This ensures that users can quickly dial in their desired sound without fuss.

Another significant aspect of the Coustic 161SE is its robust build quality. The amplifier is housed in a durable chassis designed to withstand prolonged use, while its heat dissipation technology prevents overheating during extended play sessions.

In addition to the technical specifications, the Coustic 161SE exhibits a modern aesthetic, featuring a glossy finish and backlit controls. This design not only enhances its appearance but also ensures visibility in low-light conditions.

In conclusion, the Coustic 161SE amplifier stands out in the competitive audio market with its powerful performance, versatile sound tuning options, and elegant design. Its advanced technology and user-friendly features make it an exceptional choice for anyone looking to elevate their audio experience. Whether for casual listening or professional applications, the Coustic 161SE promises to deliver immersive sound like never before.