Casio KL-8100 manual Small Typeface, To change character size using direct specification

Page 33

Small Typeface

The normal size for the small typeface is 1 1 (16 16 dots; 2mm 2mm). 8 16 dots matrix is used to form alpha-numeric characters and symbols.

Character size can be changed by specifying a vertical factor (1, 2, 3, 4) and a horizontal factor (1, 2, 3, 4, 5, 6, 7, 8).

The table below shows the character size indicator values that appear for each character size.

The character size indicator 1 1 is shown on the display when the small typeface is being used.

Small Typeface

The range (From - To settings) for a character size specification cannot extend from one block to another.

Notes

Proportional spacing cannot be used with the small typeface.

Available font is only one.

Style and text effect settings may not print correctly when used with the small typeface.

Dingbats and user characters may not print correctly when used with small typeface.

To change character size using direct specification

1.While there is text on the display, press SIZE.

2.Use u and i to highlight ”SIZE” and then press SET.

3.Specify the character size you want.

Use t and y to move the highlighting between the two dimensions.

To change a dimension, press i to increase it or u to decrease it. Or you can input a value directly on the label printer’s keyboard.

Remember that the dimensions you can specify depend on the width of the tape loaded in the label printer (see table, left).

4.After you finish setting the character size you want, press SET to register it.

5.Move the cursor to the start character from which you want to change the character size and then press SET to register your selection.

6.Move the cursor to the end character up to which you want to change the character size and then press SET to register your selection and change the character size.

At this point, the label printer returns to the text input screen. The following shows a character size mark.

Specifying Character Sizes for Lines of Text Using Preset Formats

With this method, you input the text you want and then use preset formats to specify the character size for each line of text. Note that character size marks do not appear inside of text when you specify character sizes using this method. Instead, the character size display mark shows the size of the characters where the cursor is currently located.

About the format menu

The format that appears in the following procedure uses symbols to indicate character sizes in each line of text. The formats that appear depend on the width of the tape loaded in the label printer and the number of lines in the block of text where the cursor is located when you press the SIZE key. The following shows all of the formats available for each tape width and the number of lines of text.

Note that with the preset formats, all character sizes have the same vertical and horizontal measurements.

24mm and 18mm tape, 1 line of text

 

1

1

2

2

3 3

4

4

5

5

 

Image 33
Contents KL-8100 About safety precaution symbolsExamples Memory Contents IntroductionQuick Reference Power Supply Important PrecautionsLabel Printer Menus AC AdaptorPower On Recall Function Turning Power On and OffResetting the Memory Auto Power Off FunctionRemoving the Tape Cartridge Message Language About the SET UP menuDisplay Contrast SoundDisplay Symbols and Indicators Manual feed indicator To use the Symbol menuBasic Alpha-Numeric Input About the Code keyUser Characters Inputting IllustrationsDeleting Individual Characters Moving the CursorClearing the Display Text EditingTo switch between overwrite and insert Part 6 Character Sizes Text EffectsPart 8 Printing Part 9 FramesPart 14 Reference Part 12 MemoryPage Page ∑ Contact a nearby dealer whenever you require servicing Page Page Tape Cartridges SET SET Page Page Caps off Example To input á Code 1 ´ a SET Page Page Fonts Text Effects Character StylesDirect Specification of Character Sizes To change character size using direct specification Small TypefaceAbout the format menu About Auto Sizing To find out preset format character sizesFundamentals of Label Layout Using the Layout DisplayCreating and Deleting Blocks Block OperationsDirection All Text Operations To display the ALL Form menuUsing the Image Display Printing PrecautionsTo adjust the print density Printing a TapeTo specify a frame around the printing area To display the Presets menuTo specify frames around each character To show the image displayTo use a preset layout to create a label and print it To store a label created using a preset layoutTo recall a preset layout label from memory To print a large-size label To delete a preset layout label from memoryBar Code Tape To print a bar codeTo recall a bar code from memory To store a bar codeTo delete a bar code from memory To print sequentially numbered labelsTo create a new stamp label To print a preset phraseTo store a numbering format To recall a numbering format from memoryTo recall a stamp label from memory To store a stamp labelTo delete a stamp label from memory To store dataInitial Settings Cleaning the Printer Head and RollerTo recall memory text using character search To clean the printer head and rollerTape Length Indicator Format IndicatorIllustrations Symbols, Dingbats, and Special Characters Initializing the Label PrinterFonts Enlarged Label Measurements FramesTroubleshooting Bar Code SpecificationsPower Supply PhrasesText Input Tape Cutting Using Labels Data Communication Error Messages Specifications
Related manuals
Manual 31 pages 37.09 Kb