Samsung KN04-00010A user manual Thermal Printer SRP-350/352plusA&C

Page 1

 

Printer Installation Guide

KN04-00010A (Rev.1.6)

THERMAL PRINTER SRP-350/352plusA&C

 

 

Information

This Installation Guide includes a brief outline of information necessary for product installation. For more detailed installation information, please refer to the user manual in the enclosed CD. The contents of the CD include the following.

1.Manual: User Manual, Code Chart, Control Commands

2.Drivers: Windows Drivers, OPOS Drivers

3.Utilities: a Logo download tool and a virtual memory switch control tool

Components

 

Cable cover

Paper Roll

 

Procuct Installation CD

 

SRP-350plusC SRP-350plusA

CD

Installation Guide

USB A-A JACK

AC/DC Adaptor

Power cord

Connecting the cables

1.Turn off the printer and the host ECR (host computer).

2.Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector of the printer.

3.Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface connector cable accordingly.

4.Plug the drawer kick-out cable into the drawer kick-out connector on the printer.

 

Drawer kick-out connector

 

Power connector

 

Adaptor

Interface connector

Power cord

Drawer kick-

Interface cable

out cable

(Serial/Parallel/USB/Ethernet)

 

Installing the Paper Roll

1. Open the paper roll cover by pressing the cover- open button.

2. Insert a new paper roll, making sure to align it properly.

3. Pull out a small amount of paper, and close the cover.

Note

When closing the cover, press down on the center of the cover to ensure that the paper is in contact with the roller.

Note: Adjusting the Paper Near-End Sensor

 

The SRP-350plus has a paper near-end sensor that

 

provides notice that the paper roll is nearly

 

exhausted. When the paper is running low, the lamp

Near end

on the apparatus is lit red. If the lamp is activated

sensor tab

even when sufficient paper remains, adjust the

near-end sensor setting by pushing the tab upward towards 1.

Using the Operation Panel

POWER (LED)

When turning on the power, a green LED will be lit.

ERROR (LED)

When an error occurs, a red LED will be lit. (e.g. no paper, cover ajar, etc.)

PAPER (LED)

Red LED will be lit when the paper roll is running low. The LED blinks when the printer is in self-test standby mode or macro execution standby mode.

FEED (Button)

Press the FEED button once to discharge extra paper. Holding down the FEED button will discharge paper continuously until the button is released.

Setting the DIP Switches

Changing Dip Switch settings must be done when the printer is off. Any changes done while the printer is on will not be processed.

1.Serial Interface

• DIP Switch 1

SW

Function

ON

OFF

Default

1-1

Auto Line Feed

Enable

Disable

OFF

1-2

Handshaking

XON/XOFF

DTR/DSR

OFF

1-3

Data Length

7bits

8bits

OFF

1-4

Parity Check

Yes

No

OFF

1-5

Parity Selection

EVEN

ODD

OFF

1-6

Baud Rate Selection (bps)

Refer to the following table 1

OFF

1-7

ON

1-8

 

 

 

OFF

• DIP Switch 2

 

 

 

SW

Function

ON

OFF

Default

2-1

Reserved

-

-

OFF

2-2

Internal bell control

Internal bell disable

Internal bell enable

OFF

2-3

Auto Cutter

Disable

Enable

OFF

2-4

BUSY Condition

Receive Buffer Full

* Offline

OFF

* Receive Buffer

 

 

 

Full

 

2-5

Print Density

Refer to the following table 2

OFF

2-6

OFF

2-7

 

 

 

OFF

2-8

Near-End Sensor Status

Disable

Enable

OFF

2.Parallel / USB Interface

• DIP Switch 1

 

SW

 

 

Function

 

 

 

ON

 

 

OFF

Default

1-1

 

Auto Line Feed

 

 

Enable

 

 

Disable

OFF

1-2

 

 

Reserved

 

 

-

-

 

OFF

1-3

 

 

Reserved

 

 

-

-

 

OFF

1-4

 

 

Reserved

 

 

-

-

 

OFF

1-5

 

 

Reserved

 

 

-

-

 

OFF

1-6

 

 

Reserved

 

 

-

-

 

OFF

1-7

 

 

Reserved

 

 

-

-

 

ON

1-8

 

 

Reserved

 

 

-

-

 

OFF

 

• DIP Switch 2

 

 

 

 

 

 

 

 

 

 

 

SW

 

 

Function

 

 

 

ON

 

 

OFF

Default

2-1

Reserved

 

 

-

-

 

OFF

2-2

Internal bell control

 

Internal bell disable

Internal bell enable

OFF

2-3

Auto Cutter

 

 

Disable

 

 

Enable

OFF

 

 

 

 

 

 

 

 

 

 

 

* Offline

 

 

2-4

BUSY Condition

 

Receive Buffer Full

* Receive Buffer

OFF

 

 

 

 

 

 

 

 

 

 

 

Full

 

 

2-5

Print Density

 

 

Refer to the following Table 2

OFF

2-6

 

 

OFF

2-7

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

2-8

Near-End Sensor Status

 

 

Disable

 

 

Enable

OFF

 

• Table 1 – Baud rate (bps) Selection

 

 

 

 

 

 

 

 

 

Transmission Speed

 

 

1-6

 

1-7

 

 

1-8

 

Default

 

 

2400

 

 

 

ON

 

OFF

 

 

OFF

 

 

 

 

4800

 

 

 

ON

 

OFF

 

 

ON

 

 

 

 

9600

 

 

 

OFF

 

ON

 

 

OFF

9600

 

 

 

19200

 

 

OFF

 

OFF

 

 

OFF

 

 

 

38400

 

 

OFF

 

ON

 

 

ON

 

 

 

 

57600

 

 

OFF

 

OFF

 

 

ON

 

 

 

 

115200

 

 

ON

 

ON

 

 

ON

 

 

 

• Table 2 – Print Density Selection

 

 

 

 

 

 

 

 

 

 

 

2-5

 

 

2-6

 

 

2-7

 

Print Density (Mono color)

 

Default

 

 

ON

 

 

ON

 

Reserved

 

 

1(Light)

 

 

 

OFF

 

 

OFF

 

Reserved

 

 

2

 

 

2

 

 

ON

 

 

OFF

 

Reserved

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

ON

 

Reserved

 

 

4(Dark)

 

 

 

2-5

 

 

2-6

 

 

2-7

 

Print Density (Two colors )

 

Default

 

 

ON

 

 

ON

 

ON

 

 

80%

 

 

 

 

ON

 

 

ON

 

OFF

 

 

90%

 

 

 

 

OFF

 

 

OFF

 

ON

 

 

95%

 

 

 

 

OFF

 

 

OFF

 

OFF

 

 

100%

 

100%

 

 

ON

 

 

OFF

 

ON

 

 

105%

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

OFF

 

OFF

 

 

110%

 

 

 

 

OFF

 

 

ON

 

ON

 

 

120%

 

 

 

 

OFF

 

 

ON

 

OFF

 

 

130%

 

 

 

Image 1
Contents Thermal Printer SRP-350/352plusA&C IFG-P Type IFA-S TypeIFA-E Type Imprimante Thermique SRP-350/352plusA&C Guide d’installation de l’imprimanteCaractéristiques AutotestIEEE1284 IFG-P Type IFG-U TypeImpresora Térmica SRP-350/352plusA&C Guía de instalación de la impresoraEspecificaciones AutoevaluaciónFija IFG-U Type FinalizadoImpressora Térmica SRP -350/352plusA&C Manual de instalação da impressoraEspecificações Teste automáticoRS-232C IFA-S Type Impressão do teste automático. Prima o botão Alimentar