Resolving Technical Problems
☛Please consult the following table BEFORE contacting your dealer or local SAMSUNG
☛representative.
Problem | Meaning / Solution | ||
|
|
| |
The software installation failed | ◆ Check that your hard disk is not full. | ||
| ◆ The installation floppy disk may be corrupted. | ||
| Repeat the installation with the backup floppy disk. | ||
|
|
| |
I | After installing the device driver, your system | ||
during the | |||
| expected. If it does not | ||
| verify your AUTOEXEC. BAT file and, if | ||
| necessary, contact your local computer dealer. | ||
|
|
| |
The disc tray does not open. | The drive may not be installed correctly. Verify the | ||
| physical installation. |
|
|
|
|
|
|
In the File Manager, the | If you have installed the | Then ... | |
icon does not display. |
|
| |
|
|
|
|
| And the software | ||
|
|
|
|
| And have not installed | Install the software | |
| the software | following the instructions | |
|
| on page 5. |
Technical Specifications
SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice.
SECTIONS |
|
|
| ||
|
|
|
| ||
| Disc types supported | ||||
DISC | |||||
| Video CD ready, Enhanced CD, | ||||
| Disc diameter | 12cm or 8cm | |||
|
|
|
|
| |
| Data transfer rate | Max. 6000KB/s |
| Max. 7200KB/s | |
|
|
|
| ||
| PIO Mode - 4. DMA MW2 |
| |||
|
|
| |||
|
|
|
|
| |
| Access time (1/3 stroke) | 80ms(typical) |
| 70ms(typical) | |
DRIVE PER - | Data buffer capacity | 128KB |
| ||
FORMANCE | Laser | Semiconductor Laser |
| ||
|
|
|
|
| |
| Slide mechanism | Gear motor |
| ||
|
|
|
|
| |
| Spindle motor | Brushless motor |
| ||
|
|
|
| ||
| Loading type | Tray Loading, DC motor(Soft Eject) | |||
|
|
|
| ||
ERROR RATE |
| ||||
|
|
|
|
| |
| Button | Open/Close |
| ||
|
|
|
|
| |
FRONT PANEL | Indicator(LED) | Busy |
| ||
|
|
|
| ||
Headphone output | Stereo Mini - jack (¯ 3,6 mm) | 0.60 ± 20% (Vrms) 33½ | |||
| |||||
|
|
|
|
| |
| Volume control | Dial type |
| ||
|
|
|
|
| |
| Required power | +5V DC 1.7A, |
| ||
|
| +12V DC 1.0A |
| ||
REAR PANEL |
|
|
|
| |
Interface connector | ATAPI |
|
I installed the software and re- booted my PC. The
◆When the program of Windows 95/98 is broken up,
◆it as the computer can not read the program anymore.
◆Verify the connections between the drive and your PC.
◆Check that the
◆interface (some PCs are equipped with an SCSI disk
◆interface).
◆Verify your AUTOEXEC. BAT file. Go to page 5 for
◆the verification procedure.
◆Check the LASTDRIVE = command in the CONFIG. SYS
◆file. The specified letter must take the
◆into account. If you do not know which letter is assigned
◆to the
◆Using the documentation provided with your PC, check
◆that the IDE hard disk is set up in MASTER mode.
|
| Audio output | Line out 0.70 ± 20%(Vrms), 47k½ |
|
| Jumper block | Device configuration jumper |
|
|
|
|
OPERATING | Work area | Temperature : 5~45 ¡C, Humidity : 8~80% | |
ENVIRONMENT | Storage area | Temperature : | |
|
| Dimensions | 149(W) x 42.5(H) x 200(D)mm |
GENERAL |
| (Including bezel) | |
|
|
|
|
|
| Net weight | 950g |
RELIABILITY |
| MTBF | 125,000 POH(Duty 20%) |
| Disc compartment loading | 30,000 times | |
|
|
6 | 7 |