Bose VCS-10 manual Connect the speakers, Choosing speaker cord, Be sure to use the cord properly

Page 8
Connect the speakers

English

Setting Up

Connect the speakers

Choosing speaker cord CAUTION: Before making any connections, turn off your receiver or amplifier and unplug it from the AC power (mains) outlet. Not doing so may result in damage to your system.

Be sure to use the cord properly CAUTION: Never use broken or frayed wiring, which can result in damage to your components.

Note: It is sometimes difficult to distinguish wire markings. Note: Before running speaker cord through a wall or under a floor, check your local building code requirements and safety regula- tions. You may want to contact an electrical installer for this infor- mation.

If your receiver’s center channel is not amplified, you must con- nect an amplifier to the receiver. Use an RCA cable to connect the center channel RCA-type output on the receiver to the RCA-type input on the amplifier. The speaker will then connect directly to the amplifier instead of to the receiver.

Choosing speaker cord

Be sure to use the proper gauge (thickness) of speaker cord. Stan- dard zip cord (2-conductor, 18-gauge wire found at electrical and hardware stores) works for most applications. If your speakers will be more than 30 feet (9 m) from the receiver or amplifier, see the following table, or check with your authorized Bose dealer.

Gauge*

Length*

18

(0.75 mm2)

30 ft (9 m) maximum

16

(1.5 mm2)

45 ft (14 m) maximum

14

(2.0 mm2)

70 ft (21 m) maximum

* Based on a maximum frequency response deviation of ±0.5dB.

At the ends of each cord, strip approximately 1⁄2 inch (12 mm) of insulation from both wires. Twist the bare end of each wire, so loose strands will not touch across terminals.

Be sure to use the cord properly

Speaker cord consists of two insulated wires. The insulation around one wire is marked (striped, collared, or ribbed). This marked wire is always positive (+). The plain wire is always nega- tive (–). These wires correspond to the red (+) and black (–) termi- nals on the speaker and the receiver or amplifier.

Inspect both wires carefully. Note: It is sometimes difficult to distinguish wire markings.

Inspect both wires carefully.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents VCS-10 Center Speaker VCS-30 Series II Center/Surround Speaker System Bose Home Theater SpeakersOwner’s Guide Brugervejledning Bedienungsanleitung Guía del usuario Notice d’utilisation Manuale d’istruzioni GebruiksaanwijzingPage Where to find … For your recordsSetting Up Before you beginUnpack the carton EnglishA. The VCS-10 speaker carton contents B. The VCS-30 Series II system carton contentsCenter speaker Owner’s guide Rubber feet Right surround speaker Mounting brackets Left surround speakerPlace the center speaker Position your surround speakers EnglishNote It is sometimes difficult to distinguish wire markings Inspect both wires carefullyConnect the speakers Choosing speaker cordMake the connections Marked wireMarked wire Red terminal lever Red terminal leverCheck the connections Center speakerReceiver or amplifier Right Surround speakerMounting your speakers on a wall Adjusting Your Surround Sound Settings How to set your Pro-Logic receiverFor realistic home theater sound To use the test toneHow to set your Dolby Digital receiver If the sound is interruptedProper setting Receiver channel outputReference TroubleshootingCustomer service Technical information Cleaning speakersWarranty period Reference Dansk Her findes …Gem disse oplysninger Udpakning af kassen OpstillingInden De begynder Midterhøjttaler Gummipuder BrugervejledningVenstre surround højttalerMontering sbeslag Højre surround- højttaler Gummipuder Monteringsstøtter MidterhøjttalerBrugervejledningPlacering af Deres midterhøjttaler Placering af Deres surround-højttalere Vær sikker på, at De bruger kablet rigtigt Tilslutning af højttalerneSådan vælges højttalerkabel Sådan foretages tilslutningerne Rød terminalfligMarkeret ledning Markeret ledning Rød terminalfligKontrol af tilslutningerne MidterhøjttalerModtager eller forstærker Venstre surround-højttalerMontering af højttalerne på en væg Montering af højttalerbeslagJustering af Deres surround sound-indstillinger Sådan opnås realistisk Home Theater-lydSådan indstilles De Pro-Logic-modtageren Sådan bruges prøvetonenSådan indstilles De Dolby Digital-modtageren Hvis lyden afbrydesFejlfinding KundeserviceReference Tekniske oplysninger Rengøring af højttalereGarantiperiode Opstilling Deutsch Sie finden …Wichtige Informationen Auspacken des Kartons AufstellungBevor Sie beginnen Aufstellen Center Speaker Linker Surround SpeakerBedienungsanleitung Gummifüße Rechter Surround Speaker Halter Gummifüße Befestigungs zubehörAufstellen des Center Speakers Aufstellen Ihrer Surround Speaker Korrektes Anschließen des Kabels Anschließen der LautsprecherWählen Sie das Lautsprecherkabel Anschlüsse vornehmen Roter KlemmhebelMarkierte Ader Markierte Ader Roter KlemmhebelPrüfen der Anschlüsse Center SpeakerReceiver oder Verstärker Rechter Surround SpeakerAnleitung zur Wandmontage Ihrer Lautsprecher Befestigen der LautsprecherhalterEinstellen Ihrer Surround Sound-Einstellungen Damit ein realistischer Heimkino-Sound erzeugt wirdKorrektes Einstellen Ihres Pro Logic Receivers Gebrauch des TesttonsEinstellen Ihres Dolby Digital Receivers TonunterbrechungKundendienst ProduktinformationenFehlersuche Technische Daten Reinigen der LautsprecherGarantie Produktinformationen Español Dónde encontrarPara conservar como referencia Desembalar InstalaciónAntes de comenzar A. Contenido de la caja del altavoz VCS-10 Altavoz central Pies de cauchoGuía del propietario B. Contenido de la caja del sistema VCS-30 de la serieColocación del altavoz central Colocación de los altavoces ambientales Utilizar el cable correctamente Conectar los altavocesEscoger el cable adecuado Efectuar las conexiones AlambrePresilla roja Alambre marcado Presilla rojaVerificar las conexiones Altavoz centralReceptor o amplificador Altavoz ambiental izquierdoMontar los altavoces en una pared Instalación de las abrazaderas del altavozAdaptar los ajustes del sonido de los altavoces ambientales Para lograr un sonido de cine en casa realistaCómo ajustar el receptor Pro-Logic Para usar el tono de pruebaAdaptar los ajustes del sonido de los altavoces ambientales Cómo ajustar su receptor Dolby digitalSi se interrumpe el sonido Servicio al cliente En caso de problemasReferencia Información técnica Limpiar los altavocesGarantía Referencia Francais Sommaire …Informations personnelles Installation Avant-proposDéballage FrançaisEnceinte centrale Patins en caoutchouc adhésifs Notice d’utilisationB. Contenu de l’emballagePositionnement de l’enceinte centrale ATTENTION Ne posez pas l’appareil à proximité de sources dePositionnement des enceintes arrière surround Raccordement des enceintes Choix du câble d’enceinteUtilisez correctement les câbles de raccordement d’enceinte Remarque Avant de faire cheminer un câble d’enceinteRéalisation des connexions Vérification des raccordements Fixation murale des enceintes Installation du support d’enceinteUtilisation du signal test Réglage des paramètres sonores surroundObtenir un son Home Cinema réaliste Réglage d’un ampli-tuner Pro-LogicRéglage d’un ampli-tuner Dolby Digital Son intermittentRecherche de défauts Service ClientRéférence et appelez le Service Client Bose Entretien des enceintesDurée de la garantie Informations techniquesRéférence Italiano Dove trovare …Registrazioni personali Disimballaggio InstallazionePer iniziare Diffusore centrale Piedini in gomma Collocazione del diffusore centrale Collocazione dei diffusori surround Utilizzi il cavo in modo corretto Collegamento dei diffusoriScelta del cavo per diffusori Collegamento dei cavi Linguetta delConduttore connettore rossoControllo dei collegamenti Diffusore centraleRicevitore o amplificatore Diffusore surround sinistroMontaggio dei diffusori sulle pareti Regolazione delle impostazioni Surround Per un suono Home Theater realisticoImpostazione del ricevitore/amplificatore Pro-Logic Uso del tono testImpostazione del ricevitore/amplificatore Dolby Digital Se il suono si interrompeServizio clienti In caso di problemiInformazioni e consigli Informazioni tecniche Pulizia dei diffusoriPeriodo di garanzia Installazione Nederlands Waar vindt u …Ter notering De luidsprekers uitpakken InstallatieAlvorens te beginnen Schroeven voor de installatie Center luidspreker Gebruiksaanwijzing B. De doos met het VCS-30 Series II systeem bevatCenter luidspreker Gebruiksaanwijzing Rubbervoetjes Linker Surround luidsprekerBeugels Rechter Surround luidspreker RubbervoetjesHet plaatsen van de center luidspreker Het plaatsen van de Surround luidsprekers Gebruik de kabel op de juiste manier De luidsprekers aansluitenWelke luidsprekerkabels? Gemerkte draad Contactknopje rood Aansluitingen makenContactknopje rood Aansluitingen controleren Center luidsprekerReceiver of versterker Linker Surround luidsprekerDe luidsprekers aan de muur bevestigen Installatie van de luidsprekerbeugelHet afstellen van uw Surround Sound systeem Voor een realistisch Home Cinema-geluidHet afstellen van uw Pro-Logic receiver of versterker Gebruik van de testtoonHet afstellen van uw Dolby Digital receiver Als het geluid wordt onderbrokenUitgangskanaal van de receiver JuisteVerwijzing Oplossen van problemenKlantenservice Technische gegevens Reinigen van de luidsprekersGarantieperiode Verwijzing Svenska Var du finner…För framtida bruk Så här börjar du Uppackning av högtalarnaA. Model VCS-10 förpackningen innehåller B. Model VCS-30systemets förpackningPlacering av mitthögtalaren Placering av Surround-högtalare Var noga med att använda kabeln korrekt Anslutning av högtalarnaVälja högtalarkablar Så här ansluter du Röd anslutningsklämmaMärkt ledare Märkt ledare Röd anslutningsklämmaSå här kontrollerar du anslutningarna Montera högtalarna på en vägg Installation av högtalarfästenAnvänd testsignalen Justering av Surround Sound-inställningarnaSå här ställer du in realistiskt ljud i hemmabion Så här ställer du in Pro-Logic-mottagarenStäll in din Dolby Digital mottagare Om ljudet blir avbrutetFelsökning KundserviceReferens Teknisk information Rengöring av högtalarnaGaranti Borrmall A C BDrilling template Boreskabelon Bohrschablone Page 2001 Bose Corporation The Mountain Framingham, MA 01701-9168 USA AM257528 Rev.02
Related manuals
Manual 17 pages 13.71 Kb

VCS-10 specifications

The Bose VCS-10 and VCS-30 are premium ceiling-mounted loudspeakers designed for commercial environments, delivering exemplary audio performance and sophisticated technology suited for applications ranging from corporate meeting rooms to retail spaces. These models are known for their high-quality sound reproduction, versatility, and ease of installation.

The VCS-10 is a two-way loudspeaker featuring Bose's patented Articulated Array technology. This technology enables the VCS-10 to deliver an even distribution of sound across a wide listening area, minimizing dead zones and ensuring that every listener enjoys a clear and consistent audio experience. The speaker incorporates a high-performance woofer and tweeter, allowing for rich bass and crisp highs that enhance voice clarity and ambient music.

The VCS-30, on the other hand, is an enhanced version offering a more robust sound performance. It features a larger woofer for deeper bass response and an increased power handling capability. This makes the VCS-30 ideal for larger spaces where a more powerful audio presence is required. Both models are engineered to provide a wide frequency response, making them suitable for a variety of audio content, from spoken word to complex musical compositions.

One of the standout characteristics of both the VCS-10 and VCS-30 is their sleek, low-profile design. The compact, unobtrusive appearance allows them to blend seamlessly into any architectural setting, making them ideal for professional environments where aesthetics are crucial. Their installation is facilitated by a dedicated mounting system that simplifies the process while ensuring secure placement.

In terms of connectivity and compatibility, both models support standard audio distribution systems, making them easy to integrate into existing setups. They are designed to work seamlessly with Bose’s Commercial Signal Processing products, enhancing their capabilities while providing intuitive control for sound management.

Durability is another significant feature, as both speakers are constructed with high-quality materials designed to withstand the rigors of commercial environments. Their weather-resistant design also makes them suitable for outdoor applications, ensuring long-lasting performance.

Overall, the Bose VCS-10 and VCS-30 loudspeakers embody a perfect blend of technological innovation and practical design aimed at delivering a superior audio experience. These models are well-suited for businesses seeking to enhance their acoustic environment, ensuring that audio delivery is nothing short of exceptional.
Top Page Image Contents