AEGOp5 Operation - Delay Calibration
Press the DELAY Button will display the current delay time for channel LS.
AEGOp5 Operation - Pro Logic Mode
Pressing the SL or SR button, switches the surround channels on and off. The LCD will display the following:
DOLBY DIGITAL CO
| Subwoofer | Centre |
Front | | Front |
| Right |
Left | |
| |
Press the DELAY Button again will circle to next channel.
DOLBY | DIGITAL | CO |
DELAY | SR 5 | MS |
Press the D TIME + or D TIME - button will increase or decrease the delay time for current channel.
DOLBY | DIGITAL | CO |
DELAY | SR 6 | MS |
Pro Logic Mode
Your AEGOP5 will automatically switch to Pro Logic mode when it detects a Pro Logic signal. With other types of input signal, you can select the Dolby Pro Logic mode manually by pressing Pro Logic button on the remote. Repeatedly pressing the
Pro Logic Button will switch the Pro Logic mode in between the following modes; AUTO, ALL PCM, ENABLE and DISABLE.
input | | power |
mute | | test |
balance | delay | prologic |
field | EQ on/off | EQ setup |
preset 1 | preset 2 | preset 3 |
save1 | preset 4 | load |
BassManager | Cen |
SPK SUR ON
DOLBY DIGITAL CO
SPK SUR OFF
Pressing the SW button, switches the subwoofer on and off. The LCD will display the following:
DOLBY DIGITAL CO
SPK SW ON
The recommended listening position is described below:
■ Centre channel speaker should be placed the same distance as the |
left and right speakers from your listening position. |
AEGOp5 Operation - Time Delay Adjustment on Surround Speakers
SL/SRSW
If a Pro Logic signal is detected, AEGOP5 will switch to Pro Logic mode automatically, and the display shows the following information:
DOLBY DIGITAL CO
PROLOGIC AUTO
DOLBY DIGITAL CO
SPK SW OFF
Bass Manager
Pressing the BASS MANAGER button enables you to select from three different settings of Bass; Bass Config.1, Bass Config.2 and Bass Config.3. These selections will feed the bass signal below 120Hz to different speakers as described below.
■ Rear left and right speakers should be placed behind your listening |
position and above ear level. |
■ If speaker placement is restricted due to the physical environment |
of the room, delay calibration is sometimes necessary to achieve |
the ideal listening environment. |
■ If the centre speaker can only be placed nearer to you than the left |
and right speakers, sound from the centre speaker will arrive |
before the sound from the left and right speakers. The difference in |
arrival time could may affect the sound quality and effect. Your |
AEGOP5 allows you to adjust the speaker time delay to compensate |
Delay Calibration
Press DELAY Button and repeat to select the length of delay time for SL/SR/C channels.
The delay range for SL/SR is 0 to 15 ms and 0 to 5 ms for centre.
Adjust the delay time on selected channel by pressing D TIME + or D TIME - on the remote control.
Surround Speaker Delay
mute | | test |
balance | delay | prologic |
field | EQ on/off | EQ setup |
preset 1 | preset 2 | preset 3 |
save1 | preset 4 | load |
BassManager | Cen |
SL/SR | | SW |
DRC | VOL | D Time |
| |
reset
If a stereo signal (either analog or digital) is detected, AEGOP5 will switch to stereo mode automatically. You can then convert the stereo mode to Pro Logic mode by pressing the Prologic button until you see the following on the display:
DOLBY DIGITAL CO
PROLOGIC ALL PCM
DOLBY DIGITAL CO
PROLOGIC ENABLE
If you want to convert Pro Logic or 2-channel Dolby Digital signal into Stereo mode, you can press the Prologic button until you see the
Bass Config.1
With this setting, the bass signal below 120Hz will be sent to the subwoofer; the LEDs on the front panel indicating SW will be red, and the LCD will show the following:
DOLBY DIGITAL CO
BASS CONFIG.1
Bass Config.2
With this setting, the bass signal below 120Hz will be sent to front left and right speakers and the subwoofer; the LEDs on the front panel indicating L/R/SW will be red, and the LCD will show the following
for this problem by increasing the delay time for the centre channel. |
Thus sound from the centre, left and right speakers will reach you |
at the same time. If your centre speaker is closer to your listening |
position than the left and right speakers, press DELAY button |
repeatedly until the centre channel is selected. To increase or |
decrease the delay time, press D TIME + or D TIME - until the |
desired delay is selected. The same procedure can be applied to |
adjust the delay time of rear surround speakers if necessary. |
Delay calibration for the rear surround
speakers may be necessary if the surround speakers are placed quite close to your listening position. To correct the delay this may cause, press the DELAY button repeatedly until SL or SR appear on the display. Increase the time delay of the surround speakers by pressing D TIME + until you are able to hear a 3D sound effect coming from surround speakers.
Press DELAY Button again to move to the next channel.
following on the display:
DOLBY DIGITAL CO
PROLOGIC DISABLE
AEGOp5 Operation - Speaker Mode with Bass Manager
information:
DOLBY DIGITAL CO
BASS CONFIG.2
Bass Config.3
With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on the front panel indicating L/R/SL/SR/SW channels will be red and the LCD will show the following information:
DOLBY DIGITAL CO
AEGOp5 Operation - Time Delay Adjustment on Centre Channel Speaker
Delay Calibration | mute | | test |
Press the DELAY button and repeat to | balance | delay | prologic |
select the length of delay time for the | | | |
Rear Left (SL), Rear Right (SR) and | field | EQ on/off EQ setup |
| | |
Centre(C) channels. | preset 1 | preset 2 | preset 3 |
| | |
DOLBY | DIGITAL | CO |
DELAY | SL | 5 | MS |
DOLBY | DIGITAL | CO |
DELAY | SR | 5 | MS |
Press D TIME + or D TIME - to increase or decrease the delay time for the selected channel.
DOLBY | DIGITAL | CO |
DELAY | SR 6 | MS |
Speaker Mode with Bass Manager
The six LEDs on front panel of your AEGOP5 represent the six discrete audio channels (Left, Right, Centre, Rear Left, Rear Right and Sub). If a particular channel is active, the LED will light up in green. The LED will be red if that particular channel carries bass signal below 120Hz.
Speaker Mode
field | EQ on/off | EQ setup |
preset 1 | preset 2 | preset 3 |
save1 | preset 4 | load |
BassManager | Cen |
SL/SR | | SW |
DRC | VOL | D Time |
| |
reset
BASS CONFIG.3
Bass Config. Off
With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on front panel of AEGOP5 indicating L/R/C/SL/SR/SW channels will be red and the LCD will show the following information:.
DOLBY DIGITAL CO
BASS CONFIG.OFF
| | save1 preset 4 | load |
| The delay range for SL/SR is 0 to 15 | BassManager | Cen |
| ms and 0 to 5 ms for centre. |
| | |
| | SL/SR | SW |
| Adjust the delay time for the selected | VOL | D Time |
| DRC | |
| | |
| channel by pressing D TIME + or D | reset | |
| TIME - on the remote control. | | |
Pressing the CEN button, switches the centre channel on and off. The LCD will display the following:
DOLBY | DIGITAL | CO |
SPK | C | ON | |
DOLBY | DIGITAL | CO |
SPK | C | OFF | |