Atlantic Technology SYSTEM10SRDIPOLESURROUND, SYSTEM10LCR instruction

Step 4. Strip about ˚” of insulation from the connect- ing wires. Insert them into the appropriate push termi- nal on the rear of the speaker assembly, being careful to observe polarity (positive to the red terminal, nega- tive to the black terminal).Typically, with standard “zip” cord wiring the marked wire is used for the positive lead. Markings typically consist of a thread within one conductor, printing on the wire’s insulation, a ridge or ridges on the insulation, or a flat side to the insula- tion.

Step 5. Carefully position the speaker assembly into the wall cutout and Installation Bracket. Check that it’s level and then attach the speaker to the Installa- tion Bracket with the included 3 inch #6 self-tapping screws. (If the assembly is not level, you can over- size the wall opening very slightly to allow straighten- ing the bracket and speaker.)

Step 6. Tighten the mounting screws, which in turn

Fig. 2 Installing the clamping tabs

will cause the bezel and the Installation Bracket to clamp the wall board between them. Be very careful not to overtighten the screws as this can make the grille difficult or impossible to install. The outer trim bezel has been specially designed to flex and conform to the wallboard. This makes for a good seal and eliminates rattles but it also means that the speaker mounting screws should be snug, but not overly tight.

Should you have any questions or problems please feel free to contact us at 781-762-6300 or through our web site, Customer Service@atlantictechnology.com.

Fig 1 Installing the Mounting Bracket

Step 1. Tilt one corner of the Installation Bracket into the opening and continue to slide it fully into the wall cavity until it fits completely into the cutout. Be sure to position the side extensions so they press against the inside of the wall.

Step 2. Carefully insert the tabs into the Installation Bracket as shown in Fig. 1. They are a tight fit and are best installed by “clamping” them with your hand as shown. Alternately, there are predrilled holes in the side flanges of the Installation Bracket that may be used to hold the assembly to the wall board with #6 self-threading screws, instead of using the tabs.These screws will be hidden by the speaker’s bezel when it is mounted.

Step 3. After the Installation Bracket is fixed in place note that there are holes near the center of the long sides that can be used to secure feed wiring using the included nylon wire ties.

System 10 InWall Speakers

There must be a minimum depth behind the wall face of 3 5/8 (92 mm). Be sure to keep the edges of the cutout at least 1 inch (25 mm) away from any stud or obstruction. The speaker assembly itself (the part with the drivers mounted in it, the trimming bezel, etc.) is designed to mount to the Installation Bracket after it has been installed within the wall.

● ● ● ● ● ● ● 6● ● ● ● ● ● ● ● ● ● ●

SYSTEM10LCR, SYSTEM10SRDIPOLESURROUND specifications

Atlantic Technology offers innovative audio solutions designed to enhance your home theater experience, and two of their standout products are the SYSTEM10SRDIPOLESURROUND and SYSTEM10LCR speakers. These models exemplify cutting-edge technology and thoughtful design, catering to audiophiles and casual listeners alike.

The SYSTEM10SRDIPOLESURROUND speaker is engineered to create an immersive sound environment using its unique dipole configuration. This design allows the speaker to deliver sound from two sides, dispersing sound waves throughout the listening area, which creates a more enveloping experience and minimizes reflection from walls. The dipole design is especially effective in rear surround channels, producing a more cinematic feel by blending sound seamlessly into the background. The key feature of the SYSTEM10SRDIPOLESURROUND is its adjustable switching capability, allowing users to toggle between dipole and monopole operation, depending on their listening preferences and room acoustics.

Complementing the surround experience is the SYSTEM10LCR, a versatile speaker designed for left, center, and right channel operations. Featuring a sleek, low-profile design, the SYSTEM10LCR is not only sophisticated in sound but also complements any home decor. This speaker effectively utilizes high-quality drivers and advanced crossover technology to ensure clarity and precision across the frequency spectrum. With a robust cabinet construction, the SYSTEM10LCR minimizes cabinet resonance, leading to cleaner sound reproduction.

One of the critical characteristics of both the SYSTEM10SRDIPOLESURROUND and SYSTEM10LCR speakers is their compatibility with high-resolution audio formats. They are designed to handle a wide dynamic range, resulting in the ability to reproduce subtle nuances in music and movie soundtracks. The durable build quality ensures longevity, while the aesthetic appeal accommodates various room environments.

In conclusion, Atlantic Technology's SYSTEM10SRDIPOLESURROUND and SYSTEM10LCR speakers represent a marriage of innovative technology and elegant design. Their dipole surround capabilities and versatile LCR function make them an ideal choice for anyone looking to elevate their audio experience, whether for film, music, or gaming. With these speakers, Atlantic Technology continues to set a standard in the home entertainment market, ensuring users receive an unparalleled auditory journey.