PYLE Audio PLCD79MP instruction manual Trouble Shooting

DSP

In DSP mode you can select the equalizer settings POP M, JAZZ M, CLASS M and FLAT M, and DSP OFF by rotating the VOL +/- knob.

BEEP ON/OFF

You can select two types of confirmation beep by rotating the VOL +/- knob.

BEEP ON: The confirmation beep can be heard whenever a button is pressed.

BEEP OFF: The confirmation beep is switch off. SEEK 1/ 2 (only available during radio operation)

Seek function with the	or	buttons during radio operation.
You can select SEEK 1/ SEEK 2 by rotating the VOL +/- knob.
SEEK 1: Keep the or	buttons pressed down and the radio will
stop at the next station that is detected.
SEEK 2: As long as the	or	buttons are pressed down the search

function will continue in the frequency band.

VOL LAST/VOL ADJ

You can select VOL LAST or VOL ADJ mode by rotating the VOL +/- knob. VOL LAST: The radio switches on at the actual volume it had when

it was last switched off.

VOL Addition: Rotating the VOL +/- knob you can pre-select a constant switch-on volume.

4. POWER ON/OFF

Turn the power on by using any button except the OPEN and REL button and the VOL +/- knob on the front control panel; Press PWR button and hold for approximate two seconds to turn power off.

Press the PWR button repeatedly to adjust the brightness of the VFD.

5. VFD Display

6.7.TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS a) During RADIO mode:

press the or button briefly to tune a frequency manually. Press the or button and hold for more than one second to start the automatic search for a radio station with a strong signal level. (See also the function SEEK 1/SEEK 2.)

b) During CD/MP3 mode:

press the button briefly to play next track. Press the button briefly to play the current track from the beginning of the current track. Press the button twice continuously to play the previous track. Press the or button hold to skip forward or backward.

8. BAND BUTTON

Press the BND button briefly to select the radio broadcasting band you would hear.

TROUBLE SHOOTING

Before using the check list please make all the connections first.

If you still have questions after going through the checklist, please consult your local customer service representative.

Common Symptoms	Cause	Solution
	The car ignition is switched off.	If the power supply is properly connected to
		the car accessory, switch the ignition key to
There is no power.
		" ON " or " ACC " .
	The fuse has blown.	Replace another fuse according to the wiring
		diagram.
The CDs cannot	Presence of CD disc inside the player	Remove the disc in the player then put a new
be loaded.		upward
The CDs are loaded	The transport screws have not been	Remove the transport screws before using.
only halfway into	removed.
the CD tray.
	Inserting the disc in upside down	Insert the compact disc with the label facing
The device does		upward
	The surface of CD is extremely dirty	Clean the CD or try another CD, if this works
not work correctly
(EJECT, LOAD,	or it is damaged.	correctly, the first CD is properly damaged.
PLAY)
	Temperature inside the car is too	Cool off until the ambient temperature returns
	high.	to normal
	The volume control is set too low.	Turn up the volume properly.
There is no sound.
	The device has not been correctly	Check the power and earth connection
	connected.	according to the wiring diagram.
The operation keys	1.The built-in microcomputer is not	1. Switch the device off and on again. Or press
do not work	operating properly due to noise	the RESET button to resume the program.
	2.Front panel is not properly fix into
	its place	2. Reinstall the front panel
	The installation angle is more than	Adjust the installation angle to less than 30
	30 degrees	degrees
The sound of the	The surface of the road is uneven.	Wait until the road becomes smoother before
CD player skips		playing the CD.
	The surface of CD is extremely dirty	Clean the CD or try another CD, if this works
	or it is damaged.	correctly, the first CD is properly damaged.
No radio reception.	The antenna cable is not connected.	Insert the antenna cable firmly into the
		antenna socket of the device.
In automatic search	The transmission signals are too	Tune in to a radio station manually.
mode the radio does	weak.
not stop at a trans-
mitting station.

3 12