NEC P461 Remote Control Function, To SET Remote Control ID, To SET/RESET Remote Control Mode

Page 29

Remote Control Function

English

REMOTE CONTROL ID FUNCTION

REMOTE CONTROL ID

The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors. For example: if there are many monitors being used in the same area, a remote control in normal mode would send signals to every monitor at the same time (see Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specific monitor within the group (see Figure 2).

TO SET REMOTE CONTROL ID

While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then be used to operate the monitor having that specific Monitor ID number.

When 0 is selected or when the remote control is in normal mode, all monitors will be operated.

Monitor ID:1

Monitor ID:2

Monitor ID:3

Remote works

Remote works

Remote works

Figure 1

Remote in

Normal mode or the REMOTE ID is set to 0

Monitor ID:1

Monitor ID:2

Monitor ID:3

TO SET/RESET REMOTE CONTROL MODE

ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for

Remote does

Remote does Remote works

not work

not work

2 seconds.

 

 

 

Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold

 

 

 

down for 2 seconds.

 

 

 

In order for this feature to work properly, the display must be assigned a Monitor ID

Figure 2

 

 

number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the

Remote set up to

 

use REMOTE

OSD (See page 23).

ID:3

 

Point the remote control towards the remote sensor of the desired monitor and press the

REMOTE ID SET button. The MONITOR ID number is shown on the display when your remote control is in ID mode.

Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.

1.Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100.

This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.

2.On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number (1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose Ò0Ó to simultaneously control all displays in range.

3.Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button. The MONITOR ID number is shown in red on the display.

If the REMOTE CONTROLID is Ò0Ó, then all displays in range will show their respective MONITOR ID number in red.

If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.

This LCD monitor can be controlled via personal computer or wireless remote control using an RS-232C connection.

MONITOR ID and IR CONTROL

Using one PC or one infrared wireless controller, up to 100 individual LCD monitors can be controlled through a daisy chain via RS-232C connection.

1.Connect PC and LCD monitors.

Connect a PCÕs RS-232C control output to the LCD monitor RS-232C input. You can then connect the RS-232C output from the LCD monitor to another LCD monitor RS-232C input. Up to 100 monitors can be connected using RS-232C.

2.Set Monitor ID and IR Control mode.

For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under the ÒMULTI DISPLAYÓ menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two monitors should share the same Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially from 1. The first monitor in the daisy chain is designated as the primary monitor. Subsequent monitors with the chain are secondary monitors.

In the ÒADVANCED OPTIONÓ menu on the first monitor in the RS-232C daisy chain set the ÒIR CONTROLÓ to ÒPRIMARYÓ. Set the ÒIR CONTROLÓ to ÒSECONDARYÓ on all other monitors.

English-27

Image 29
Contents MultiSync P401 MultiSync P461 Advanced Option IndexEnglish-1 Canadian Department of Communications Compliance StatementFCC Information Declaration Important InformationDeclaration of the Manufacturer English-2Cleaning the Cabinet Cleaning the LCD PanelRecommended Use ErgonomicsContents Installation Attach Mounting Accessories Attaching Mounting AccessoriesInstalling and removing optional table top stand Ventilation RequirementsAmbient Light Sensor Parts Name and FunctionsControl Panel DVI in DVI-D Terminal PanelRGB/HV OUT BNC Audio OUTExternal Speaker Terminal Kensington LockOption board slot English-9Keypad Wireless Remote ControlHandling the remote control Operating Range for the Remote ControlDetermine the installation location SetupInstall the remote control batteries Connect the supplied power cordAdjust the sound Switch on the power of all the attached external equipmentAdjust the screen See pages 20 Adjust the image SeeConnections Wiring DiagramBefore making connections English-14Connecting a DVD Player with Hdmi out Connecting a Personal ComputerConnecting a Computer with DisplayPort English-15Basic Operation Power on and OFF ModesEnglish-16 OFFUsing Power Management Power IndicatorSelecting a video source Picture AspectAmbient Mode Picture ModeAmbient parameter setting Information OSDEnglish-19 OSD On-Screen-Display ControlsEnglish-20 English-21 English-22 English-23 English-24 English-25 English-26 Image Sticking of LCD PanelRecommendations Remote Control ID Remote Control FunctionTo SET Remote Control ID To SET/RESET Remote Control ModeInout Wired Remote Control FunctionEnglish-28 English-29 ConnectionNetwork Setting by Using an Http Browser Connecting to a NetworkControlling the LCD monitor via LAN Control OverviewPreparation Before Use Network SettingsHandling of the Address for Operation via a Browser English-31English-32 Alert Mail SettingEnglish-33 FeaturesTroubleshooting English-35 Specifications P401Product Specifications English-36 Specifications P461English-37 Pin AssignmentRXD TXD GNDDisposing of your old NEC product Manufacturer’s Recycling and Energy InformationEnergy Saving Weee Mark European Directive 2002/96/EC
Related manuals
Manual 41 pages 36.85 Kb