Audiovox DV 7300 operating instructions Trouble Shooting Guide, Symptom Cause and Remedy

Page 23

TROUBLE SHOOTING GUIDE

SYMPTOM

CAUSE (AND REMEDY)

 

 

 

No power.

Ensure the AC power cord is connected.

No picture

The region number of the disc doesn't match the region number of this unit.

 

• The TV is not set to receive DVD signal output.

 

The video cable is not connected.

 

• The TV is not turned on.

 

Clean the disc.

The picture is not

If video from your system has to go through your VCR to get to your TV, the copy-

clear.

 

protection applied to some DVD programs could affect picture quality.

 

The disc is scratched.

 

The DVD unit may be set to progressive scan; moreover, TV does not support

 

 

progressive scan component video signal. Set the Video Out to “CVBS" mode.

 

The location and orientation of the antenna are incorrect. If you use an indoor

 

 

antenna, change to an outdoor antenna.

 

The TV antenna wire is too close to the unit. Separate the TV antenna wire from

 

 

the unit.

 

 

 

 

 

 

No sound or only a very low-level sound is heard.

Ensure the speakers and equipment are connected securely.

The system is in Pause mode or in Slow-motion Play mode. Press the PLAY button to return to normal play mode.

Fast forward or fast reverse is performed. Press the PLAY button to return to normal play mode.

Make sure the AUDIO output and AV IN input connections are correct.

Adjust the speaker volume.

Severe hum or noise is heard.

Ensure the speakers and equipment are connected securely.

Ensure the connecting cords are away from a transformer or motor, and at least 10 feet (3 meters) away from a TV set or fluorescent light.

Move your TV away from the audio equipment.

The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.

Clean the disc.

Vibrations from the speakers are affecting the unit.

The remote does not function.

Remove any obstacles between the remote and the unit.

Use the remote near the unit.

Point the remote at the remote sensor on the unit.

Replace the batteries in the remote.

The disc does not play.

There is no disc inside ("No Disc" appears on the TV screen).

Insert the disc correctly with the playback side facing down on the disc tray.

Clean the disc.

A non-VALID disc has been inserted. The unit and disc region number are incom- patible.

The DVD door

• Condensation may have formed inside the unit due to a sudden change in

cannot open.

temperature. Wait approximately an hour for it to clear and try again.

- 22 -

Image 23
Contents Home Theater On Condensation Safety PrecautionsOn Placement On SafetyImportant Safety Instructions Table of Contents Icons Used on DVDs Disc FormatsRegion Management Information Disc Function or Operation that is Not AvailableRemote Control AccessoriesControl Reference Guide Remote ControlUnit Rear Panel Unit Front PanelDisplay Examples TV Screen Unit Display Remarks Region Local Number Error IndicatorDisplay Display InformationConnecting your TV SetupConnecting the FM Wire Antenna Analog Connection Connecting a VCRConnecting Other Equipment Amplifier Watching a VideotapeListening to Another Audio Equipment Connecting the Speakers & SubwooferPositioning the Speakers and Subwoofer Plugging in the UnitSound System Playing a Disc Display Function Angle SelectionSubtitle Selection Audio SelectionLocating a Specific Track Setting Favorite Bookmarks During PlaybackSpecial Function Locating a Specific Title/Chapter/TimeRepeat Playback DVD Programmed Playback DVD Programmable MemoryViewing Jpeg Files Clear the Programmed Tracks/Files Play Modes for CD or Jpeg DiscCD Track/JPEG File Programmed Playback Customizing the Function Settings Smart Picture View ModeVideo Out Listening to the Radio Tuning in to a Station ManuallyPresetting Stations Tuning in to a Preset StationSymptom Cause and Remedy Trouble Shooting GuideCleaning the Unit MaintenanceSpecifications Cleaning the Disc