Bi-wiring and bi-amping loudspeakers, Beforeyou Start

Bi-wiring and bi-amping loudspeakers

BEFOREYOU START

WARNING: Do not make any connections to your amplifier while it is switched on or connected to the mains supply.

Before switching on please check all connections thoroughly, making sure bare wires or cables are not touching the amplifier in the wrong places (which could cause short circuits) and you have connected positive (+) to positive and negative (–) to negative.

Always ensure that the volume control on your amplifier is set to minimum before starting these procedures.

BI-WIRINGYOUR LOUDSPEAKERS

Bi-wiring improves the sound of your system because it divides the high and low frequency signal currents into separate speaker cables. This avoids signal distortions arising from the high and low frequency currents interacting with one another within a single cable, as in conventionally wired systems.

You will need:

Speakers – with four input terminals each: these will be marked HF (High Frequency) and LF (Low Frequency).

Loudspeaker cables – two pairs of cables per loudspeaker (which may be joined at the amplifier end if your amplifier has only one pair of output terminals per channel). Or, a suitably terminated cable set (a loom, probably prepared by your dealer and capable of being used for bi-wiring in one length).

How to bi-wire loudspeakers

1.Remove the terminal links on the rear of your loudspeakers

WARNING:This step is essential or damage to your amplifier may result which is not covered under warranty.

2.Connect the cables as shown in the diagram below, ensuring correct polarity at all times.

SP2	Arcam P35 power amplifier	SP2
+ R –	+	L –
SP1		SP1

HF	–	Right	HF	–	Left
+		speaker	+		speaker
LF			LF

Recommended bi-wiring configuration

BI-AMPINGYOUR SYSTEM

The performance of your system can be further enhanced over that	English

achieved with bi-wiring, by extending the principle one stage further
to include separate amplification for the low and high frequency drive
units in each loudspeaker enclosure.
Connect the integrated amplifier to the high frequency (HF) terminals
and connect the power amplifier to the low frequency (LF) terminals.

You will need:

Speakers – with four input terminals each (as with bi-wiring): these will be marked HF (High Frequency) and LF (Low Frequency).

Four channels of amplification – for example two P35 stereo amplifiers or four P1 monoblock amplifiers.

Loudspeaker cables – two pairs of cables per loudspeaker or a suitably terminated cable set (a loom, probably prepared by your dealer and capable of being used for bi-amping in one length).

Interconnect cables – one pair of high quality interconnect cables.

How to set up a bi-amped system

1.Remove the terminal links on the rear of your loudspeakers.

WARNING:This step is essential or damage to your amplifier may result which is not covered under warranty.

2.Connect the cables as shown in the diagram below, ensuring correct polarity at all times.

3.Use the interconnect cables to connect the PRE OUT sockets of the C30 to the corresponding AUDIO IN sockets of the power amplifier. If using the P1 amplifier, it may be necessary to “daisy- chain” the interconnect cables. See page 11 for more details on doing this.

+	– Arcam P35 power amplifier +			–
	R		L
+	–	+		–
Right	HF		HF	Left
speaker	LF –	–	LF	speaker
		–
+		+		–
+	–	+		–
	R	Arcam P35 power amplifier	L
		Arcam P35 power amplifier

Recommended bi-amping configuration

C30, P1, P35 specifications

Arcam P1 and C31 are two essential components within the Arcam product line, known for their exceptional audio performance and advanced technologies. Both units are designed to cater to audiophiles and home theater enthusiasts, providing a blend of power, clarity, and versatility.

The Arcam P1 is a powerful class AB power amplifier that is engineered to deliver an impressive audio experience. With a power output of around 120 watts per channel into 8 ohms, it is capable of driving a wide range of speakers with ease. The P1 utilizes advanced circuitry and high-quality components to ensure low distortion and high fidelity. Its high current capability ensures that it can handle dynamic audio passages, making it suitable for both music and cinematic experiences.

One of the standout features of the P1 is its ability to integrate seamlessly into any audio setup. With multiple input options, including balanced XLR and unbalanced RCA connections, the amplifier can accommodate a variety of source components. Moreover, its compact design allows it to easily fit into a home theater rack without occupying unnecessary space.

The Arcam C31, on the other hand, serves as an advanced audio preamplifier and processor. It is designed to handle digital sources, providing a wealth of connectivity options, including HDMI inputs, DAC capabilities, and digital audio outputs. The C31 employs cutting-edge digital audio processing technologies to enhance sound quality and support high-resolution audio formats. It even supports various streaming protocols, allowing users to effortlessly access their digital music libraries.

Another key characteristic of the C31 is its intuitive user interface, which makes navigation through the numerous features straightforward. The device is equipped with a remote control, enabling users to adjust settings without having to physically interact with the unit. The C31's flexibility makes it an excellent choice not only for traditional home theater setups but also for modern, multi-room audio systems.

Together, the Arcam P1 and C31 create a formidable audio partnership that delivers stunning performance across various listening environments. Their combination of power, advanced technology, and user-friendly design makes them must-have components for anyone seeking to elevate their audio experience. Arcam’s commitment to quality and innovation is evident in these products, ensuring that users enjoy the best in sound reproduction.