Mitsubishi Electronics WD-60735, WD-65835 manual Setting Up NetCommand Control of an A/V Receiver

566. NetCommand IR Control (736 and 835 Series TVs)

Operating NetCommand-Controlled Devices, continued

6. NetCommand IR Control (736 and 835 Series TVs) 57

Setting Up NetCommand Control of an A/V Receiver

Key Name in	Special Operation Description and Setup				How to Use
Learning Screen
Guide	Displaying the Disc Menu (DVD or high-defini-				While watching the device, press GUIDE to display the
	tion disc format)				disc menu.
	“Learn” the Disc Menu, Top Menu, or other key as
	named on the original remote in the Guide learn-
	ing position.
	Displaying the On-Screen Program Guide				1.	While watching the device, press GUIDE to
	(cable box or satellite receiver)					display the guide.
	1. “Learn” the Guide key on the original remote in				2.	Press CH/PAGE	/	to send the Page Up/Dn
						commands for the guide.
		the Guide learning position.
	2.	Learn the PAGE	and PAGE	keys of the
		original remote in the Page Up and Page Dn
		learning positions.
Page Up	Using Page Up/Down				•	Inside the Guide
Page Dn	If the device’s original remote control has separate					Press CH/PAGE	/	to send the Page Up/Dn
						commands.
	keys for Channel Up/Dn and Page Up/Dn, the TV
	remote control’s CH/PAGE  /			key can work like	•	Outside the Guide
	the two separate keys.
						Press CH/PAGE	/	to send the Channel Up/
	1.	“Learn” CHANNEL	/ in the Channel Up/Dn
						Dn signal.
		positions.
	2.	“Learn” PAGE /	in the Page Up/Dn posi-
		tions.
Enter	Enter Functions (cable boxes, satellite receivers, etc.)
	Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
	SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand uses
	the same ENTER key for both operations.
	When ENTER has a menu or guide function or when				1.	Press MENU or GUIDE to display the device’s menu
	the original remote control uses the same key for					or guide.
	menus and channel selection:				2. Press ENTER within the menu and NetCommand
	Learn the ENTER, SELECT, or OK key in the					will send the Enter signal for menus.
	NetCommand Enter learning position.
Enter (digits)	When ENTER is for channel changes, i.e., the original				Press digit key(s) and then press ENTER.
	remote control has a separate ENTER key for this				NetCommand will send the Enter signal for channel
	function):				selection.
	Learn the ENTER key for channel selection in the
	NetCommand Enter (digits) learning position.
	Use this learning position only if the original
	remote control has separate keys for Enter in
	menus and Enter for channel selection.
Cancel	CANCEL as the Cancel or Exit Function				1.	Press MENU or GUIDE to display the menu or guide.
	“Learn” the Cancel or Exit function in the				2.	—	and NetCommand will send the
						Press CANCEL
	NetCommand Cancel learning position					Cancel or Exit signal.
—	The symbol “—” can serve as the separator							—
(separator)		between a digital channel’s main and sub-			Press digit key(s) and press CANCEL . NetCommand
					will send the channel-separator signal.
		channel digits, e.g., digital channel 12-1 (main

channel is 12, sub-channel is 1).

“Learn” the channel separator function in the NetCommand – (separator) learning position.

Several varieties of A/V receiver control are described here using the Inputs > AV Receiver menu, shown on this page.

•Controlling power and volume is described on this page.

•For most equipment setups, see “A/V Receiver Control: Automatic Audio Switching” on the next page.

•If your A/V receiver has an HDMI output, you have the option of sending both audio and video through the A/V receiver over a single HDMI cable to the TV. See “A/V Receiver Control: Automatic Video and Audio Switching via HDMI,” page 60.

Note: To set up control of other device types, see “Initial NetCommand Setup for Most Devices,” page 53.

A/V Receiver Control: Power and Volume

Perform this setup to operate the A/V receiver’s power and volume functions with the TV’s remote control.

To perform this setup you need:

•The remote controls for both the TV and the A/V receiver.

•The IR emitter cable supplied with the TV.

Before You Begin

1.Connect your A/V receiver to the TV and any addi- tional devices. See chapter 3, “TV Connections,” for suggestions. Important: You must connect the A/V receiver to the TV’s audio output; use the TV’s AVR AUDIO OUTPUT or DIGITAL AUDIO OUTPUT jack.

2.Connect the IR emitter cable to the TV and position the IR emitter where it can send signals to the A/V receiver. See “IR Emitter Placement,” page 52.

3.Set the TV’s remote control slide switch to the TV position and power on the TV if not already on.

Setup to Control A/V Receiver Power and Volume

1.Open the AV Receiver screen in one of two ways:

•If using the Auto Output Sensing screen for the A/V receiver, highlight the Learn icon and press ENTER to open the AV Receiver screen.

•If performing NetCommand setup at any time after the A/V receiver has been recognized through Auto Output Sensing:

Press MENU, highlight Inputs, and highlight AV Receiver to open the AV Receiver screen.

2.The first function highlighted in the AV Receiver screen is always Power On. Aim the TV’s remote

1

2

4

3

AV Receiver menu overview

1The Learn column lists “learnable” keys on the A/V receiver’s remote control.

2A check mark next to a key name indicates it has been “learned” by NetCommand.

3Input1 through Input5 are arbitrary names the TV uses to uniquely identify A/V receiver inputs.

4After “learning” IR codes for A/V receiver inputs, use the Assign Input column to identify the device connected to the associated A/V receiver input.

For example, if you “learned” the A/V receiver’s TV audio input as Input1, select TV Audio from the Assign Input1 column. Likewise, if you “learned” the A/V receiver’s DVD input as Input2, select DVD in the Assign Input2 column.

control at the TV and press ENTER to begin learning for Power On.

AV Receiver screen. Perform NetCommand IR “learning” for A/V receiver power and volume keys.

3.When the Power On text starts flashing, aim the A/V receiver’s remote control at the TV and press and hold the POWER or POWER ON key until a check mark appears next to Power On.

•If the text stops flashing before the check mark appears, repeat this step.

•To remove the key from NetCommand control, press the CANCEL key while the key name is highlighted.

Downloaded from www.Manualslib.com manuals search engine