Planar 40 manual Precautions, Placement precautions, Handling precautions

Page 3

Precautions

Placement precautions

¥Avoid placing the unit in humid or dusty places, or where it will be exposed to excessive heat (direct sunlight, heaters, etc.)

¥Do not step on or set anything on the AC power cord. DAMAGE TO THE AC POWER CORD IS A SAFETY RISK AND CAN CAUSE A FIRE.

¥Install the unit only on a stable and smooth surface.

¥Do not connect the unit to the same AC outlet with appliances that generate large amounts of interference (such as heaters with thermostats, appliances with motors, etc.). It is best to use a completely separate electrical outlet.

¥Keep the unit away from water or small objects. If they accidentally enters the unit, unplug the AC power cord immediately. DO NOT PLUG IN THE UNIT AGAIN.

¥Never cover the rear ventilators with cloth or something.

Handling precautions

¥"WARNING: The AC power cord and cables on this product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling."

¥Avoid bending, kinking or damaging the AC power cord.

¥Never insert or remove the power cord with wet hands. Also, be sure to hold cord by the plug when removing it from the outlet.

¥Do not remove any parts that are held in place with screws. (The unit does not contain any user-serviceable items.)

¥Maintain standard room temperature (5ûC to 35ûC, or 41ûF to 95ûF) during use. Do not subject the unit to shock or vibration. Do not move the unit while it is in use.

¥A rapid increase in room temperature in cool weather can cause condensation to form inside the unit. If this occurs, wait at least 15 minutes after turning the unit on before attempting to operate it.

European Norm Compatibility / CE

This machine is provided with the CE-mark and therewith corresponding to the norms that are valid for its operation at present. Thus the effective guidelines on the electromagnetic compatibility 89/336/EWG and safety regulations according to low voltage guideline 73/23/EWG and 93/68/EWG are guaranteed. Mutual disturbances with other electronic appliances are normally excluded, if those also are in accordance with valid norms.

Sporadically disturbances cannot, however, be excluded. The product is in conformity with the directives of the valid European guideline.

Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S.A. and other countries.

2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Planar 40 LCD Manual Table of contents Precautions Placement precautionsHandling precautions Front View Check AccessoriesNames and Functions Before First UseAC-OUT Rear ViewOuter Dimension External Control Connect the Computers InstallationConnect the Video deck, DVD player etc Component Video Terminal Side view of the monitor Rear view of the monitor How to secure the monitor on a wallLCD Monitor Instructions Adjusting the ScreenPippicture in picture Menu refer to Adjustment ItemsVideo Menu Change or indicate the input signal ModeWhile displaying the current mode, press the button again Display the OSD On Screen Display Menu Adjustment ProcedureBefore Adjustment Display the Windows or other screenSelect the item to be adjusted on the Main Menu Select the item to be adjusted on the Sub MenuAdjustment or Setting Adjust the contrast Adjustment Procedure Picture MenuManual Adjustment Adjust the brightnessAdjustment for computer screen Adjust the horizontal position Analog mode onlySelect contrast on the Sub menu and press the Enter button Adjust the vertical position Analog mode only Adjust the phase Analog mode onlySelect phase on the Sub menu and press the Enter button Select scaling on the Sub menu and press the Enter button Adjust the scalingUse the and button to adjust Select frequency on the Sub menu and press the Enter buttonSelect advanced on the Main menu and press the Enter button Adjust the color temperature PresetUse the and/or button to adjust Advanced MenuAdvanced Menu Adjust the color temperature UserAdjustment Procedure Advanced Menu Adjust the sizePicture in picture Menu Select pos on the Sub menu and press the Enter button Pip MenuSelect the position Use the and/or button to select the sizeSelect source on the Sub menu and press the Enter button Adjustment Procedure Pip MenuChange the input signal Adjust the brightness Video signal onlyAdjust the contrast Video signal only Adjust the tint Ntsc signal only Adjust the color Video signal onlyAdjust the sharpness Video signal only Select tint on the Sub menu and press the Enter buttonSelect sharpness on the Sub menu and press the Enter button Advanced picture in picture Menu Adjustment Procedure Adv pip MenuAdjust the horizontal position Adjust the vertical positionUse the and/or button to select the video format Select the video formatSelect language used in OSD On Screen Display Adjustment Procedure Options MenuOptions Menu Select the osd positionUse the and/or button to select the language Automatic Adjustment Analog mode onlyPress the button to start the Automatic Adjustment Select language on the Sub menu and press the Enter buttonDisplay the osd version Display the resolutionUtilities Menu Change the osd timeoutUse the and/or button to adjust. Interval 5~60 Utilities MenuPress the button to reset the osd setting Adjustment Procedure Utilities MenuDelete the data saved at the current display mode Select reset on the Sub menu and press the Enter buttonPicture Menu Sharpness 6 7 Scaling Wide Adjust the color Adjust the tint Ntsc signal only Use the and/or button to adjust. Interval 1~8 LB stands for Letter Box Main menu Select user red with the button and press the Enter button Adjust the color temperature UserVideo Menu Video MenuSelect video on the Main menu and press the Enter button Picture Language Advanced Display the osd version Picture Osd background Opaque Osd timeout Seconds Picture Osd background opaque Use the Enter button to select the shortcut menu Additional FunctionsShortcut Menu Display the Shortcut MenuUse the and/or button to select the size of pip Use the Enter button to select pip enable menuSelect the size of pip picture in picture Use the Enter button to select contrast menuPlug and Play Power Management SystemDisplay Screen MaintenanceFault Finding Fault FindingTroubleshooting Screen Display Specifications Table of Preset DataAnalog Video Input mini D-Sub 15pin Cable Pin ArrangementPhysical Monitor SpecificationsPC Input Video InputFederal Communications Commission FCC Statement Planar Systems, Inc
Top Page Image Contents