JVC XV-S40BK, XV-S42SL manual Troubleshooting, Symptom Possible case Remedy

Page 52

Additional information

Troubleshooting

What appears to be a malfunction may not always be serious. Please go through the following list before requesting service.

Symptom

Possible case

Remedy

 

 

 

Power does not come on.

Power plug is not inserted securely.

Plug in securely.

 

 

 

 

Too far from the unit.

More closer to the unit.

 

 

 

 

The tip of the remote unit is not pointed in

Point the infrared light- emitting window

Remote control does not work.

the right direction.

toward the remote sensor on the front panel.

 

 

Batteries are exhausted.

Replace the batteries with new ones.

 

 

 

 

 

Battery polarity is incorrect.

Take out the batteries and insert them again in

 

the correct direction.

 

 

 

 

 

 

Connection of video cable is incorrect.

Connect the cable correctly.

No picture is displayed on the

 

 

Input selection of TV is incorrect.

Select correctly.

monitor.

 

 

 

Disc is not playable.

Use a playable disc. (See page 12.)

 

 

 

No picture is displayed on the

 

 

monitor when using the

Jack(s) at use is (are) not active.

Make them active. (See page 14.)

COMPONENT or S-VIDEO output

 

 

jack(s).

 

 

 

 

 

Picture is noisy.

The unit is connected to a VCR directly

Connect the unit so that the picture signal

and the copyguard function is activated.

flows directly to the TV.

 

 

 

 

No audio is reproduced.

Connection is incorrect.

Check the connections.

 

 

Input selection of amplifier is incorrect.

Select correctly.

 

 

 

 

No audio is reproduced when playing

The audio signal is derived from the unit's

Use the AUDIO OUT when playing back such

back a DVD disc recorded with 96 kHz,

DIGITAL OUT.

discs.

linear PCM audio.

 

 

 

 

 

Sound is distorted or noise is

Disc is dirty.

Wipe the disc surface.

generated.

 

 

 

 

 

Picture does not fit the television

MONITOR TYPE is not correctly set.

Select monitor type correctly. (See page 42.)

 

 

screen.

Television is not correctly set.

Set the television correctly.

 

 

 

 

 

Microcomputer malfunction due to

Turn off the power and unplug the power

 

lightning or static electricity.

cord, then connect the power cord again.

Operation is not possible.

 

 

Moisture condensation caused by a

Turn off the power, then turn it on a few hours

 

 

sudden change of temperature or

 

later.

 

humidity.

 

 

 

 

 

Additional

information

50

Page 51 Page 53
Image 52
Page 51 Page 53
Contents 96%.966 Important for Laser Products Table of Contents Supplied accessories FeaturesIntroduction These symbols Indicate the typesDiscs which Operation can beSafety precautions Important cautionsNames of parts and controls Preliminary knowledgeFront panel Remote control unit Used as Display window Rear panelOperational Principles On-screen displaysOpening displays Preference displaysTo prevent the monitor from burning out Screen Saver Play mode displaysStatus displays How to use numeric buttons On-screen guide iconsAbout invalid operation icon To select a track/title numberAbout discs Playable disc typesDisc structure Playable discsGetting started ConnectionsBefore making any connections To connect to a TVHow to make the Component Video OUT jacks active To connect to a TV with the component video input jacksTo connect to an audio amplifier or receiver To connect to audio equipment with a digital inputRed White Audio cable not supplied Amplifier or receiver Audio cableTo connect the power cord Precautions for the safe use of batteries To install batteries in the remote control unitPrecaution Basic operations Turning on/off the unitInserting and removing discs Press 0 OPEN/CLOSE to close the disc trayBasic playback To start playbackTo stop playback completely To stop playback temporarilyResuming playback To locate the beginning of the scene or songTo memorize the interrupted position To resume playbackAdvanced operations To locate a desired scene from the DVD menuPress Title or Menu ExampleTo locate a desired selection using 4 or ¢ Use the numeric buttons to specify the numberPress Play Mode Use Cursor 2/3 to move to CHAP. SEARCH, then press EnterUse the numeric buttons 0 to 9 to enter Desired chapter numberWhen you make a mistake To locate a desired scene from the display DigestUse the numeric buttons 0 to 9 to enter the time Press DigestUse Cursor 5/∞/2/3 to select the desired scene Special picture playbackPress and hold 8 for more than 1 second To playback in slow-motion Slow To zoom a scene ZoomPress Zoom Press 8, then use 1 / ¡Changing the playback order To playback in the desired order ProgramUse Cursor 2/3 to move to Program and press Enter Press 3 to start program playRepeat playback To playback in random order RandomTo repeat the current selection or all tracks Repeat Use Cursor 2/3 to move to RandomMake sure that the Repeat mode is off. If any Repeat Mode is selected, you cannot move To A-BAudio CD/Video CD/SVCD To quit repeat playbackSelecting a scene angle To select a scene angle from the normal screen AnglePress Angle Use Angle or Cursor 2/3 to select the desired angleTo select the subtitle language Subtitle Press and hold Angle for more than 1 secondUse Cursor 5/∞/2/3 to select the desired angle Press Enter To turn the subtitle on and off, pressTo change the audio language or sound Audio Press AudioFor Svcd For Video CD/SVCDProgramsin To check the disc/time information Checking the statusTo turn off the disc/time display Press Display To check the DVD function status Dimning brightness of the display windowPress Display Press Cursor ∞ while holding down AngleBasic operations using the basic control buttons MP3 CD playbackAbout MP3 CD disc Unavailable functionsTrack/Group selection using the numeric buttons How to select a Track or GroupAdvanced functions Program playbackTo quit program playback Press 7 while stopped Random playbackYou can playback Groups on an MP3 CD disc in random order Repeat playback Use Cursor 2/3 to move to REPEAT, then press EnterYou can repeat playback of the current Group or all Groups During playback or while stoppedInitial settings How to set preferencesSelecting preferences LanguageSetting changes as follows To connect the unit’s digital Output to an external deviceEquipped with a digital input This item must be setDisplay System Press Enter while holding down 7 on the remote control unit Enter your 4-digit password using the numeric buttons 0 toLimiting playback by children To set Parental Lock for the first timeScreen display appears To change the settings Parental LockOn the TV screen To temporarily release the Parental lock Parental Lock Use the Cursor 5/∞ to move to YES, then press Enter AV Compu Link remote control system Connection and setup Additional information To AV Compu Link II or EX DVD playerOperation You connect the component video output to your TVHow to handle discs Maintenance of discsCare and handling of discs Label sideTroubleshooting Symptom Possible case RemedySpecifications Appendix ATable of languages and their abbreviations Appendix BCountry code list for parental lock
Top Page Image Contents