JVC XV-N310B manual Restarting playback after stopping resuming playback, Changing the resume mode

Page 12

Basic playback

7 3

7

3 (SELECT)

Restarting playback after stopping (resuming playback)

The player resumes playback from the position you interrupted playback, as long as the disc you interrupted playback is still on the disc tray.

This is because the player’s resume mode is set to ON when you purchased the player.

When the resume mode is set to ON, the player memorizes the position on a disc where you interrupted playback.

When you press 7 to interrupt playback, the TV screen shows [RESUME STOP] and the [RESUME] indicator lights up in the display window.

When you re-start playback, the TV screen shows [RESUME PLAY].

Hint

The memory of the interrupted position is not cleared even if you turn off the player.

To play back from the beginning

Press 7 while the disc is stopped.

The memory is cleared.

Then press 3 (SELECT).

NOTES

The player remembers the interrupted position even if you turn the power off.

The memory is cleared if you open the disc tray.

Changing the resume mode

The player has three resume modes; ON, OFF and DISC RESUME.

You can select the mode using the preference display (see page 26).

When the resume mode is “OFF”

Playback always starts from the beginning.

When the resume mode is “DISC RESUME”

The player memorizes interrupted positions for the last 30 discs played. Storing a new interrupted position will erase the interrupted position stored for the first disc.

The memory of the interrupted positions are not cleared even if you open the disc tray or turn off the player.

NOTES

If you change the [RESUME] setting from [DISC RESUME] to [OFF] or [ON], you cannot resume playback of a disc whose “resuming” position is stored. However, when you again set [RESUME] to [DISC RESUME], you will then be able to resume playback of the disc.

If you interrupt the playback of a disc for which an interrupted position has already been stored, the memory will be updated with the new interrupted position.

For a double-sided DVD VIDEO disc, the player regards each side as a different disc. Therefore, to resume playback of such a disc, the disc must be inserted with the same side down.

When the player memorizes an iterrupted point for a disc, it also memorizes Audio, Subtitle and Angle settings.

The player may not resume playback exactly from the interrupted point. In the case of an SVCD/Video CD disc with PBC function, the player may resume playback from a point slightly earlier or later than the point where playback was interrupted.

About On-screen guide icons

You may see the following icons displayed over the picture. They have the following meanings.

: Appears at the beginning of playback mode.

: Appears at the beginning of pause mode.

: Appears at the beginning of fast forward/backward playback with the current speed (see page 11).

: Appears at the beginning of slow-motion playback with the current speed (see page 11).

: Appears at the beginning of a scene recorded from multiple angles (see page 16).

: Appears at the beginning of a scene recorded with multiple audio languages (see page 16).

: Appears at the beginning of a scene recorded with multiple subtitle languages (see page 15).

You can change the setting so that the on-screen guide icons do not appear on the TV screen (see page 26).

About screen saver function

A television monitor may have an image burned into it if a static image is displayed for a long time. To prevent this, the player automatically activates the screen saver function if a static picture, such as an on-screen display or menu, is displayed while no button is pressed for over 5 minutes.

When the screen saver function is activated, the TV screen gets darker.

Pressing any buttons will release the screen saver function. You can set the screen saver function to ON or OFF (see page 25).

10

Image 12
Contents Audio/Video files playback Changing the initial settings Region code of DVD VideoMises en garde, précautions et indications diverses Important for Laser Products Important Pour Produits LaserSupplied accessories Table of contentsPrecautions About this manualBefore operation About discsRemote control unit Names of parts and controlsFront panel Display windowConnecting to a TV PreparationsConnections Connecting to a TV with component jacks About the scanning modeProgressive scan video playback available SourceConnecting to optional audio equipment Connecting to a stereo audio amplifier/receiverConnecting to a digital audio device Digital equipmentUsing the remote control unit Connecting the power cordTo install batteries Precautions of the safe use of batteriesInitial setup Basic playbackTurning the player on and off Starting playback Changing the resume mode Restarting playback after stopping resuming playbackAbout On-screen guide icons Various kinds of playback Playback at various speedsUsing the numeric buttons Locating the beginning of a scene or songPlaying from a specific position Locating a desired scene from the DVD menuChanging the playback order Specifying a desired titleTo play back in a specific order Program play About PBC Playback ControlTo exit the program mode To play back in random order Random playTo stop program playback To clear the programRepeat playback Changing the language, sound and scene angleTo repeat a desired part A-B repeat playback To select the subtitle language SubtitleSpecial picture and sound effects To change the audio language or sound AudioTo select a scene angle of DVD Video Angle To zoom in picturesTo adjust the picture character VFP To dismiss the VFP mode selection windowTo change sound field Sound Effect To deactivate the Sound EffectBasic operation procedure Menu bar functionsTo bring up the menu bar To dismiss the menu bar and status barMenu bar functions for DVD Video Menu bar functions for SVCD/Video CD/ Audio CDPrecautions Audio/Video filesPlayback OutlineBasic operations To pause playbackTo zoom in a picture To rotate/reflect a still pictureTo quit program playback mode Direct selection for Jpeg filesPlay To stop random playbackSlide show playback Changing the picture of the opening displayChanging the initial settings How to set preferencesSelecting preferences About the Preference displayLanguage menu Picture menuENGLISH, FRENCH, Spanish AUTO, FILM, VIDEONORMAL, VideoactiveAudio menu Others menuLimiting playback by children To set Parental Lock for the first timeStop mode, bring up the Others menu Press 5/∞ to move To select Parental Lock then press EnterTo change the settings To temporarily release the Parental LockAV Compu Link remote control system Connection and setupAdditional information OperationTroubleshooting PowerPicture AudioSpecifications Appendix a Country/Area code list for Parental Lock ForAppendix C Digital output signal chart Output Disc typeAppendix D Glossary Limited Warranty Authorized Service Centers DVD Player