JVC PD-42WV74 manual Troubleshooting, Problems Check

Page 61

Troubleshooting

Refer to the table below to check the condition. If you think that there is a problem, contact the JVC Service Center where you purchased the television.

PROBLEMS

CHECK

 

 

 

- Check for a blown fuse or circuit breaker or a power outage.

There is no power

- Check that the plugs on the power cords from the TV and receiver are

 

connected to wall outlets.

 

 

The power lamps do

 

not light even though

Check that POWER INDICATOR in the MENU is not set to OFF.

the TV is on

 

 

 

 

- The antenna could be disconnected.

There is no picture or

- The input mode could be set improperly. See page 54.

- The tuner (AUTO TUNER SETUP) could be set improperly. See page 33.

sound

- The TV station may be having difficulties. Check to see if other stations

 

 

are working.

 

 

 

- Check to see that the batteries are still working and properly installed.

Remote control is not

- Make sure the remote has a clear sight path to the TV.

operating properly or

- Check that the TV/CATV switch is in the proper position.

at all

- You may be too far from the TV. You must be within 23 feet (7 meters).

 

- Use the remote control while pointing it at the screen.

 

 

 

- Make sure the channels have been programmed. See “Channel

You cannot select a

Summary” on page 33.

certain channel

- Check to see if the channel is locked. See “Channel Summary - Lock”

 

page 34.

 

 

The power turns off

- Make sure the set did not become unplugged.

- Perhaps the ON/OFF TIMER is set. See page 51.

by itself

- Check to see if the Sleep Timer was set. See page 57.

 

 

 

 

This television is operated by a microprocessor. It is possible that external

It does not operate

noise or interference is causing the problem. If the television does not

function correctly, remove the power plugs of the TV and Receiver from

correctly

the wall outlets and wait a while before inserting them into the wall outlets

 

 

again and operating the television.

 

 

The clock is wrong

The power was interrupted and the clock was not reset. See page 50.

 

 

The color quality is

- Tint and Color may be improperly adjusted. See page 47.

- The VIDEO STATUS mode may be turned to the wrong setting. See

poor

page 56.

 

 

 

There are line across

There could be interference from another electrical appliance, such as a

computer, another TV or VCR. Move any such appliances further away

the picture

from the TV.

 

 

 

 

There could be interference from a high-wattage appliance, like a hair

The picture is spotted

dryer or vacuum, operating nearby. Move the antenna away from the

appliance or change to a coaxial cable connection which is less prone to

 

 

interference.

 

 

61

Image 61
Contents Plasma Display Users Guide Risk of Electric Shock Do not Open Important Safety PrecautionsImportant Safety Instructions Inch/100 mm Burn-in Do not view for long periods of time in the Regular modeAvoid burn-in as follows Point defects If Burn-in has occurredEffect on infrared devices Phenomenon described below is not a malfunctionTable of Contents Quick Setup Unpacking your TV Quick Setup Attaching the stand to the TV Display Front How to open the coverReceiver Front Quick Setup TV Remote Control Set Up Your TV Connection DiagramGetting Started TV backDisconnecting the system cable Connecting the TV and receiverConnecting the power cord to the AC outlet Remote Control Key Feature ButtonsDisplay front Basic OperationReceiver front Coaxial Cables Component Cables Connecting Your DevicesComposite Cables Audio CablesDiagram #1 Diagram #3 AV Compu Link Cable Connecting to JVC AV Compu LinkConnecting to an External Amplifier Connecting to a CamcorderDTV decoder Connecting to a Digital TV Receiver w/HDCPAV Receiver To be LanguageInteractive Plug In Menu Manual Clock Set Auto Clock SetProgramming will take approximately To 2 minutes Auto Tuner SetupRemote Programming Setting the CATV, VCR and DVD CodesCable Box or Satellite Codes VCR Codes DVD Codes Cable/Satellite Search Codes Function Search CodesVCR/DVD Search Codes Function Onscreen Menus Using the GuideOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option Blue Initial Setup Picture Adjust Sound Adjust CLOCK/TIMERS Auto Tuner Setup Initial SetupChannel Summary Chip Channel Guard MessageDirections to Block Unrated Programs Unrated ProgramsUS V-Chip Ratings Directions to set US V-Chip Ratings Setting US V-Chip RatingsDirections to set Movie Mpaa Ratings Movies RatingsDirections to set Canadian V-Chip Ratings Canadian V-Chip RatingsSet Lock Code Position Adjustment Power IndicatorAuto Demo TV Speaker Digital-InImage Shift Audio OutLanguage Noise Muting Closed CaptionV1 Smart Input Front Panel LockXDS ID Auto Shut OffPicture Settings Picture AdjustAdjust the Picture Settings Color TemperatureDigital Noise Clear ResetColor Management Burn-in Image ReducerSound Settings Sound AdjustAdjust the Sound Settings MTS Multi-Channel Television SoundSet Clock Clock/TimersOn/Off Timer Multi Screen Function Button FunctionsSplit Freeze IndexSwap SelectNumber Buttons 10Key Pad Power100+ Button InputSound Return +/TVVideo Status MutingNatural Cinema TheaterPro D6500KSleep Timer Message Sleep TimerDisplay Aspect Ratios AspectBack MenuVCR/DVD Slide Switch TV/CATV Slide SwitchVCR Buttons DVD ButtonsProblems Check TroubleshootingFollowing are not malfunctions Caring for the Screen Caring for the CabinetWarranty Name Of Dealer Model No Serial NoAccessories Authorized Service CentersSpecifications subject to change without notice SpecificationsPD-42WV74 JVC Company of America JVC CANADA, INC