JVC HD-61G587 manual Key Feature Buttons, Getting Started

Page 13

Quick Setup

Getting Started

These quick setup pages will provide you, in three easy steps, with the basic information you need to begin using your new monitor right away. If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual.

Step 1 – The Remote Control

Before you can operate your remote control, you first need to install the batteries (included).

Lift and pull the latch on the back of the remote control to open. Insert two batteries (included) carefully noting the “+” and “–” markings, placing the “–” end in the unit first. Snap the cover back into place.

When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your VCR, DVD, and/or cable box/satellite receiver may have to be reset. See pages 25 - 28.

Key Feature Buttons	MUTING	OK
The four key feature buttons at the center of the remote can	CH +

be used for basic operation of the monitor. The right and
left buttons will turn the volume up or down. These buttons	VOL	VOL
are also marked with four arrows and are used with JVC’s	–	+
are also marked with four arrows and are used with JVC’s
onscreen menu system. To use the onscreen menus, press the
MENU button.	CH –
	CH –
	MENU	BACK
	VCR CHANNEL+	VCR/DVD
Basic Operation		POWER

Turn the monitor on and off by pressing the POWER button at the top right corner of the remote. The POWER LED will light blue.

• Make sure the MONITOR/CATV switch is set to MONITOR. Move the switch to
CATV only if you need to operate a cable box.	MONITOR CATV

•	Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to DVD to
	control a DVD player. Please see pages 25 - 28 for instructions on programming
	your remote control to operate a cable box, VCR or DVD player.	VCR DVD

Note:

• If the lamp replacement message appears when you turn the monitor ON, see page 62.

13

Downloaded from www.Manualslib.com manuals search engine

Image 13

Contents

Projection Monitor Users Guide Important Safety Precautions Important Safety Instructions FCC Notice Caring for the Screen Caring for the CabinetOrder to use the monitor for a long time When the power is turned on, the warming up commencesCooling the inside of the monitor and the lamp Lamp is a consumable itemILA element characteristics Monitor requires a lot of electrical powerScreen is made of plastic Do not replace the lamp immediately after useTable of Contents Unpacking your monitor Quick SetupMonitor Models Rear Panel DiagramSide Panel Diagram Front Panel DiagramRM-C1273G Remote ControlGetting Started Key Feature ButtonsVideo Cable Component Cables Composite Cables Audio Cables Connecting Your DevicesVCR Connection Green Connecting to a Camcorder Connecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT PR Monitor OUT Looking at the images from a computer Connecting to the computerWhen a picture is not displayed Table of signals for each type of computerInteractive Plug In Menu LanguageClock Set Cable Box or Satellite Codes Programming your remote controlMGA VCR CodesDVD Player DVD CodesVCR/DVD Search Codes Function Search Codes Cable/Satellite Search Codes FunctionOnscreen Menus Using the GuideOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option BlueSound Adjust Chip Directions to Block Unrated Programs Unrated ProgramsUS V-Chip Ratings Directions to set US V-Chip Ratings Setting US V-Chip RatingsDirections to set Movie Mpaa Ratings Movies RatingsDirections to set Canadian V-Chip Ratings Canadian V-Chip RatingsSet Lock Code Language Analog SettingClosed Caption Noise Muting Auto Shut OffV1 Smart Input Front Panel LockVideo Input Label Power Indicator Position AdjustmentDigital-in Audio Digital-InAdjust the Picture Settings Picture SettingsColor Temperature Dynamic Gamma Color ManagementSmart Picture Digital VNR Natural CinemaMpeg NR ResetAdjust the Sound Settings Sound SettingsTurn On Volume Volume LimitThank YOU Set ClockFollowing message will appear Lamp Timer ResetTwin Multi Screen FunctionSwap FreezeSelect MenuVolume + PowerNumber Buttons 10Key Pad SetSleep Timer Message Sleep TimerSound MutingVideo Status Display Time Input Off DisplayAspect Aspect Ratios in PC ModeAspect Ratios By pressing the Aspect button, you can change the size VCR/DVD Slide Switch MONITOR/CATV Slide SwitchVCR Buttons DVD ButtonsChanging the Lamp Lamp ReplacementLamp Message Replacement Lamp KitUnplug the monitor How to Replace the LampRemove the lamp cover Remove the lamp unitInstall the new lamp unit Power LED and Lamp LED blink rapidly simultaneously Power LED and Lamp LED blink alternatelyLamp LED blinks Troubleshooting Following are not malfunctions Invalid SignalNo Program Specifications subject to change without notice SpecificationsPage Page Page JVC Company of America JVC CANADA, INC