Mitsumi electronic HC3200 user manual Projecting images, Preparation

Page 18

Viewing video images (continued)

C. Projecting images

Preparation:

•Remove the lens cap.

•Turn on the power of the connected video equipment.

STATUS indicator

POWER indicator

ON ( I ) button

HDMI button

S-VIDEO button

COMPONENT button

VIDEO button

p, q, t, u buttons

HC3200

HDMI / COMPUTER / t button

POWER button

VIDEO/ u button

1.Confirm the POWER indicator lights-up red.

•If the projector was turned off before the lamp had cooled down sufficiently, the fan may start rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.

. Press the POWER button on the projector or ON ( I ) button on the remote control.

•It may take about one minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.

•The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 44.)

. Adjust the focus by turning the focus ring.

4.Select an input source.

•Press the VIDEO or HDMI/COMPUTER button on the projector or the VIDEO, S-VIDEO, COMPONENT or HDMI button on the remote control that is corresponding to the terminal in use.

•The input source is switched between VIDEO, S-VIDEO and COMPONENT every time you press the VIDEO button on the projector.

•The input source is switched between COMPUTER and HDMI every time you press the HDMI/COMPUTER button on the projector.

•The projector automatically selects the appropriate signal format. (The selected signal format is displayed on the INFORMATION menu.)

•You cannot change the input source while the menu is being displayed.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Some images become easier to view when the setting of aspect ratio is changed. (See page 20.)

•When this projector is connected with an HDMI device supporting HDCP, such as a DVD player, image is not displayed correctly at the time of switching the input source on rare occasions. In such cases, switch to other input source and then switch back to the HDMI input source.

•When COMPONENT is chosen as the source, images supplied from the computer may flicker. Press the t or u button on the remote control to reduce flicker, if it occurs. (Fine adjustment)

5.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

EN-18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents
HC3200 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Important safeguards Preparing your projector Inserting the batteries into the remote controlRemoving the batteries from the remote control What’s included in the boxControl panel Preparing your projectorOverview Terminal panelRemote control Using the picture quality adjusting buttonsBottom side Using the remote control Operational range of the remote controlReception angle When the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceSetting up your projector When the aspect ratio of the screen is 2.351 CinemaScopeWhen the aspect ratio of the image is With the Installation menu See page 26 for menu setting When fine streaks are seen on projected imagesWhen projected images are distorted to a trapezoid To cancel the menuRear projection InstallationFront projection, ceiling mounting Trigger terminalBasic home theater system connection Connecting the projector to video equipmentViewing video images PreparationWhen a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesConnecting to video equipment having a Hdmi terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images To stop projecting Setting the aspect ratio ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2How to change the settings With the remote controlWith the Feature menu See page 26 for menu setting Viewing computer images Connecting the projector to a computerPlugging the power cord About DDCViewing computer images ComputerExample of the setting procedure for external output When connecting to a notebook computerSetting of the resolution Auto Position buttonFeature Signal Keystone Lamp Mode Menu operationSetting Function How to set the menusAvailable settings in the menus Menu operationInstallation menu Feature menu Signal menu User menuAV memory To store the settingsTo enable the stored image quality settings Information menuTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness How to Use BrilliantColorTMAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp To enable the stored color temperatureBlue Magenta RED How to Use Color ManagementTo adjust the ratio of change in brightness Gamma Mode HighTo enable the stored gamma mode To adjust the vertical positionLPF Progressive filter To enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampWhen the projector is mounted to the ceiling Replacing the lampTo replace the lamp Reset of the lamp operation time Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens Troubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution EN-43 Normal condition IndicatorsStatus Condition Possible Solution Abnormal conditionSpecifications Dimension drawings unit mmSpecifications Computer IN/COMPONENT Video ConnectorsReplacement part option/not included in the box VLT-HC3800LPMitsubishi Electric Corporation