LG Electronics 42LY340H, 32LY340H OSD Select Command k l, Remote Control Lock Mode Command k

Page 32

32EXTERNAL CONTROL DEVICE SETUP

ENGLISH

08.Brightness (Command: k h) To adjust screen brightness.

You can also adjust brightness in the PICTURE menu.

Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping.

Acknowledgement [h][ ][Set ID][ ][OK/NG][Data] [x]

09.Color (Command: k i) To adjust screen color.

You can also adjust color in the PICTURE menu. Transmission [k][i][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping.

Acknowledgement [i][ ][Set ID][ ][OK/NG][Data] [x]

10.Tint (Command: k j) To adjust screen tint.

You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][ ][Data][Cr]

Data Red: 00 ~ Green: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping.

Acknowledgement [ j ][ ][Set ID][ ][OK/NG] [Data][x]

11.Sharpness (Command: k k) To adjust screen sharpness.

You can also adjust sharpness in the PICTURE menu.

Transmission [k][k][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 32 (*transmit by Hexadecimal code)

*Refer to Real data mapping.

Acknowledgement [k][ ][Set ID][ ][OK/NG][Data] [x]

12. OSD Select (Command: k l)

To select OSD (On Screen Display) on/off. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 00: OSD off Data 01: OSD on

Acknowledgement [l][ ][Set ID][ ][OK/NG][Data] [x]

13.Remote Control Lock Mode (Command: k

m)

To lock the remote control and the front panel controls on the set.

Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 00: Lock off Data 01: Lock on

Acknowledgement [m][ ][Set ID][ ][OK/NG] [Data][x]

If you’re not using the remote control and front panel

controls on the Monitor set, use this mode. When main power is on/off, remote control lock is released.

If Key Lock is on in the standby mode, TV will not turn on by POWER button of remote control and on the TV.

14.Balance (Command: k t) To adjust balance.

You can also adjust balance in the AUDIO menu.

Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to Real data mapping. Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]

15.3D (Command: x t) (For 3D TV) To change 3D mode for TV. Transmission [x][t][ ][Set ID][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][Cr] Data01

00: 3D On

01:

3D Off

02: 3D to 2D

03:

2D to 3D

Data02

 

 

00: Top and Bottom

01: Side by Side

02: Check Board

03: Frame Sequential

Image 32
Contents LED TV Important Safety Instructions EnglishEnglish Grounding Outdoor Antenna GroundingMoving VentilationGenerated Sound Preventing image burn or burn-in on your TV screenDot Defect FCC Notice LG Recycling PolicyLicenses Open Source Software NoticeTable of Contents Assembling and Preparing UnpackingParts and Buttons Adjusting the menu Basic functionsSetting up the TV Lifting and Moving the TVFor 42/47/55LY340H M4 x L14 M4 x L20 English 20˚20˚ Securing the TV to a wall optional Mounting on a Wall Cm 10 cmConnecting to an Antenna or Cable Making ConnectionsOther Connections Speaker 8 ΩBlu-Ray / HD Cable Box / HD STB / DVD / PC Remote Control Maintenance Cleaning your TVTroubleshooting Specifications ModelsHdmi DTV supported mode Component supported modeIR Codes Code Function HexaRS-232C Setup Type of Connector D-Sub 9-Pin MaleSet ID RS-232C ConfigurationsWire ConfigurationsNot standard Command Reference List Communication ParametersError Acknowledgement Transmission / Receiving ProtocolTransmission OK AcknowledgementPower Command k a Volume Control Command k f To adjust volumeBalance Command k t To adjust balance OSD Select Command k lRemote Control Lock Mode Command k Channel Tuning Command m a Color Temperature Command x u To adjust color temperatureAuto Configuration Command j u Key Command m c Equalize Command j v To adjust equalizeTable List Channel Tuning StepChild Safety LG Customer Information Center