TacT Audio M2150 Connect your, S2150 to your, RS232 connection at this time, Tact Audio Tings

Page 28

 

 

TacT M/S2150 Software

 

 

 

Connect your

Your M/S2150 must be connected to your computers serial port in order for it to

 

M/S2150 to your

communicate with your computer when you run the M/S2150 software. Please fol-

 

Computer

low the steps below to connect your M/S2150 to your computer.

 

 

1 - Connect the RS 232 “Input” jack on the back of the M/S2150 to your

 

 

computers serial port using the supplied cables and adapters. Your computer

 

 

must have a standard RS 232 serial port with a DB 9 connector.

 

 

NOTE: If you have any other Tact digital amplifiers please disconnect their

 

 

RS232 connection at this time.

 

 

2 - Turn on your M/S2150.

 

 

3 - Turn on your computer and start the M/S2150 System Software.

 

 

NOTE:You may receive a communication error message. Please close the mes-

 

 

sage window and proceed to the next step.

 

 

4 - Select the “Com” button on the main software screen to open the communica-

 

 

tion window.

 

 

5 - Under the Operating Mode select “Connect”.

 

 

6 - Under the COM Port section select “COM1”. If you receive an “invalid

 

 

port number” message please try selecting each of the port selections until

 

 

you do not receive this message. If you receive this message on all COM ports

 

 

you may not have a COM port installed on your computer. Please refer to your

 

 

computer manufactures documentation for help to install a COM port.

 

 

7 - To verify that M/S2150 is properly connected to the host computer click on

 

 

the “Start” button to perform the communication test. If everything is

 

 

functioning properly you should see the results below. Press the “Stop”

 

 

button after about 15 seconds to stop the test.

 

 

Rx Buf should display “0”.

 

 

Count should have counted in increments of 100.

 

 

Err Count should be “0”.

 

 

If the results are as above select the “Close” button to close the communication

 

 

window. Your M/S2150 is now connected to your computer.

 

 

If the results are not as above please go back to step number 6 and select

 

 

another COM port. Then repeat step 7.

 

 

NOTE: If you are still are not passing the communication test you may not

 

 

have a COM port installed on your computer or you may have another de-

 

 

vice such as a modem or hand held PC that may be sharing the COM port

 

 

on your computer. If you have a other Tact equipment attached it may be

 

 

set to the same address. The M/S2150 requires a valid COM port that is not

 

 

being used by any other devices.

 

 

NOTE: You will only have to select the communication port once. The next

 

 

time you run the M/S2150 correction software it will remember your set-

28 Tact Audio

tings.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents M2150 / S2150 Blank Tact Audio Page Acknowledgments RegistrationTable of contents Accessories Operating voltage Unpacking the M/SIntroduction Digital input Analog input optional ADC module 2150 ConnectionsDigital Input Section 2150 Connections Digital output Sampling frequency of the inputComputer Use the AUX port to connect to TacT digital amplifiersDigital Output Speaker output Normal operationBiamped operation 2150 Connections Speaker outputHorizontal Biamping 2150 Connections Vertical Biamping Configurations Examples of how a TacT active system can be configured2150 Connections Biamping M2150 & S2150Front Panel Controls Remote Control Correction block Volume BlockMenu Main screen Main menu Saving Menu Settings Tact Audio Front Panel DisplayFront Panel Display Delay menu Level menuLOW High LOWCRO menu OFF on Trig menuDispl menu DisplayMaxlev Dthr +12.0Left Right Output SourceLected option use the UP and Down buttons Baud Rate Current Address Lock menuGain 12 dB Gain menu Tact AudioTacT M/S2150 Software Connect your S2150 to yourRS232 connection at this time Being used by any other devicesSpecifications TacT Audio, Inc

M2150, S2150 specifications

TacT Audio is a prominent player in the high-fidelity audio equipment market, known for its innovative digital amplification technologies. Among its flagship products are the S2150 and M2150 amplifiers, both of which embody the brand's commitment to superior sound quality and cutting-edge design.

The TacT Audio S2150 is a stereo amplifier that exemplifies the company's philosophy of delivering high-performance audio reproduction. With its Class D amplification technology, the S2150 offers exceptional efficiency and low heat generation, making it suitable for long listening sessions without the risk of overheating. It boasts an output power of 150 watts per channel into 8 ohms, delivering dynamic and powerful sound that can drive a wide range of loudspeakers effectively.

One of the standout features of the S2150 is its built-in digital signal processing (DSP) capabilities. This allows for precise room correction, enabling users to optimize their listening environment for the best possible audio experience. The user-friendly interface makes it easy to adjust settings for different room acoustics, ensuring that music is reproduced with clarity and precision.

The M2150, on the other hand, is designed for those seeking a more streamlined, multi-channel solution. It offers all the advantages of the S2150 but expands the capability to serve multiple speakers in a home theater setup. It maintains the same high-quality Class D technology, providing 150 watts of power per channel across a wider range of configurations. The M2150 is ideal for audiophiles looking to build immersive audio environments, integrating seamlessly with modern home theater systems.

Both the S2150 and M2150 are equipped with advanced connectivity options, including digital inputs like USB, coaxial, and optical. This versatility ensures that they can be easily integrated into any audio setup, whether connecting to a computer for high-resolution music playback or linking to a digital audio source for simple streaming.

Another noteworthy characteristic of TacT Audio’s amplifiers is their robust build quality and sleek design. The combination of aesthetic appeal and durability ensures that both models not only perform exceptionally well but also enhance the visual aspect of any audio system.

In summary, the TacT Audio S2150 and M2150 amplifiers highlight the brand's dedication to high-fidelity audio through advanced technologies and user-friendly features. With their powerful output, DSP capabilities, and versatile connectivity options, these amplifiers represent a significant investment for anyone serious about achieving the highest quality sound in their home audio experience.
Top Page Image Contents