NEC P701AVT Setup, Determine the installation location, Install the remote control batteries

Page 15

Setup

English

1. Determine the installation location

CAUTION: Installing your LCD monitor must be done by a qualified technician. Contact your dealer for more information.

CAUTION: MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY FOUR OR MORE PEOPLE. Failure to follow this caution may result in injury if the LCD monitor falls.

CAUTION: Do not mount or operate the display upside down, face up, or face down.

CAUTION: This LCD has a temperature sensor and cooling fan. If the LCD becomes too hot, the cooling fan will turn on automatically. If the LCD becomes overheated while the cooling fan is running, a “Caution” warning will appear. If the “Caution” warning appears, discontinue use and allow the unit to cool. Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and “Image Persistance”.

If the LCD is used in an enclosed area or if the LCD panel is covered with a protective screen, please check the inside temperature of the monitor by using the “HEAT STATUS” control in the OSD (see page 25). If the temperature is higher than the normal operating temperature, please turn the cooling fan to ON within the FAN CONTROL menu within the OSD (see page 25).

IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Install the remote control batteries

The remote control is powered by two 1.5V AA batteries. To install or replace batteries:

A.Press and slide to open the cover.

B.Align the batteries according to the (+) and (–) indications inside the case.

C.Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or bursting.

NEC recommends the following battery use:

Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.

Do not mix battery brands.

Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries.

Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.

Do not touch exposed battery acid, it may injure skin.

NOTE: If you do not intend to use the Remote Control for a long period of time, remove the batteries.

3. Connect external equipment (See pages 15 and 16)

To protect the external equipment; turn off the main power before making connections.

Refer to your equipment user manual for further information.

NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image.

4. Connect the supplied power cord

The equipment should be installed close to an easily accessible power outlet.

Please fasten power cord to the LCD monitor by attaching the screw and clamp.

Fully insert the prongs into the power outlet socket. A loose connection may cause image degradation.

NOTE: Please refer to the “Safety Precautions and Maintenance” section of this manual for proper selection of AC power cord.

Screw

Clamp

English-13

Image 15
Contents MultiSync P701 Advanced Option IndexDeclaration of conformity For USAFor Canada English-2 Important InformationDeclaration Declaration of the ManufacturerErgonomics Cleaning the LCD PanelCleaning the Cabinet Recommended UseContents Mounting InstallationPlease note the following when mounting on wall or ceiling Attach eyebolts M12Attaching Mounting Accessories Ventilation Requirements Prevent TippingEnglish-7 Parts Name and Functions Control PanelAmbient Light Sensor Audio OUT Terminal PanelDVI in DVI-D RGB/HV OUT BNCEnglish-10 Kensington LockExternal Speaker Terminal Option board slotKeypad Wireless Remote ControlHandling the remote control Operating Range for the Remote ControlConnect the supplied power cord SetupDetermine the installation location Install the remote control batteriesAdjust the image See Switch on the power of all the attached external equipmentAdjust the sound Adjust the screen See pages 21English-15 Wiring DiagramConnections Before making connectionsEnglish-16 Connecting a Personal ComputerConnecting a DVD Player with Hdmi out Connecting a Computer with DisplayPortPower on and OFF Modes Basic OperationEnglish-17 Picture Aspect Power IndicatorUsing Power Management Selecting a video sourceInformation OSD Picture ModeAmbient Mode Ambient parameter settingEnglish-20 OSD On-Screen-Display ControlsEnglish-21 English-22 English-23 English-24 English-25 English-26 Image Sticking of LCD Panel RecommendationsEnglish-27 To SET/RESET Remote Control Mode Remote Control FunctionRemote Control ID To SET Remote Control IDWired Remote Control Function English-29Inout English-30 ConnectionOverview Connecting to a NetworkNetwork Setting by Using an Http Browser Controlling the LCD monitor via LAN ControlEnglish-32 Network SettingsPreparation Before Use Handling of the Address for Operation via a BrowserEnglish-33 Alert Mail SettingEnglish-34 FeaturesTroubleshooting Specifications Product SpecificationsEnglish-36 GND Pin AssignmentEnglish-37 RXD TXDWeee Mark European Directive 2002/96/EC Manufacturer’s Recycling and Energy InformationDisposing of your old NEC product Energy Saving