Hitachi 36SDX88B manual Hookup Cables and Connectors, Antenna Connections, VHF 75-Ohm antenna/CATV

HOOKUP CABLES AND CONNECTORS

ANTENNA CONNECTIONS

These sets are equipped with one VHF/UHF antenna terminal. The VHF/UHF terminal can be used for normal TV, cable TV (CATV), a TV game, etc.

1. VHF (75-Ohm) antenna/CATV			3.. When both VHF and UHF antennasareconnected
When using a 75-Ohm coaxial cable system,				to the PC ready
			Attach an optionalnal ANTENNAMIXER to the TV
disconnect the VHF adaptor from the VHF 75-Ohm			color TV antenna terminal and connect the cables to
			antenna terminal and connect the cables to the
receptacle and connect the outdoor antenna or			the ANTENNA MIXER.
			ANTENNA MIXER.
CATV cable to a VHF 75-Ohm receptacle.			(Rear of PC ready
				￿￿￿￿￿￿￿
			color￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿TV set)
	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿		￿￿￿￿￿￿￿￿￿￿￿￿￿￿	￿￿￿￿￿￿￿￿￿￿
				￿￿￿￿￿￿￿￿￿￿￿￿
		￿￿￿￿￿￿￿
￿￿￿￿￿￿		￿￿￿￿￿￿￿￿￿￿￿￿
		￿￿￿￿￿￿￿￿￿￿￿
￿￿￿￿￿￿￿￿￿￿￿￿￿
			￿￿￿￿￿￿￿￿
			￿￿￿￿￿
2. VHF (300-Ohm) antenna/UHF antenna			Notes:
When using a 300-Ohm twin lead from an outdoor			1. If an outdoor antenna/CATV is used, disconnect
antenna disconnect the (VHF or UHF) indoor			the indoor antenna. Ghosting and poor reception
antenna leads from screws of the (VHF or UHF)			may result if both the indoor and outdoor antennas/
adaptor and connect outdoor (VHF or UHF)			CATV are connected at the same time.
leads to these screws of a (VHF or UHF) adaptor.
		￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿	2. Consult your dealer or service store for the
		￿￿￿￿￿￿￿￿￿￿￿￿￿￿	ANTENNA MIXER and (VHF or UHF) adaptor.
		￿￿￿￿￿￿￿￿￿
		￿￿￿￿￿￿￿￿￿￿￿
			3. The special converter (decoder) will be supplied
			by the cable company.

NOTE: Optional adapter for *Apple® Macintosh® computers. (*See page xx). If the optional AESP model G301/U Macintosh to VGA® adapter connector is configured and connected between Macintosh video out and the 36SDX88B video in, the Macintosh is forced to boot in 640 x 480/60 Hz or 800 x 600/60 Hz mode (set mode) because the operational adapter correctly manipulates the Macintosh sense pins.

For the optional adapter to work, it s DIP switch settings should be # 2, 3, 6, 7 = ON and # 1, 4, 5, 8, 9, 10 = OFF.

See below: Example - See Switch Instructions for details.

Mode 5 = 2367 (SVGA 800 x 600/60 Hz configuration) (VGA 640 x480/60 Hz configuration)

Composite Separate Sync

SW1	SW2	SW3	SW4	SW5	SW6	SW7	SW8	SW9	SW10
	ON	ON			ON	ON
OFF			OFF	OFF			OFF	OFF	OFF

ON

2 3 6 7

ONDIP

1 2 3 4 5 6 7 8 9 10

1 4 5 8 910

OFF

10