How To Set Up Your New Hitachi Plasma Television
To take measures to prevent the Plasma Television from tipping over and prevent possible injury it is important to mount the unit in a stable and flat surface.
Securing to a
1.Using wood screws (two) fasten the set to the clamping screw holes on the rear of the Plasma Display stand as shown below.
2.Using commercially available wood screws, secure the set firmly in position.
Wire
Wood screw two places
Securing to a Wall
1.Keep the Plasma television 4 inches away from the wall except when mounted using the wall mount bracket.
2.Secure the television to the wall as shown in fig. (a) or (b).
AB
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (a) Power Swivel |
|
| (b) Power Swivel |
| ||||||||||
| NOT USED |
|
| USED |
| ||||||||||
NOTES: 1. Do not block the ventilation holes of the Plasma Television. Blocking the ventilation holes might cause fire or defect.
2.In case of an abnormal symptom, unplug the AC cord.
3.If you purchased the wall mount bracket option, please ask for professional installer. Do not install by yourself.
4.If the Power Swivel feature will not be used, the Plasma television should be secured to the wall as shown in
fig. (a).
5.If the Power Swivel feature will be used, the Plasma television should be secured to the wall as shown in
fig. (b). The wires need to be long enough to allow the television to turn 30˚ to the left and right.
ANTENNA
Unless your Plasma Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts,
an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. In order to prevent an internal temperature increase, maintain a space of 10 cm (4 inches) from the sides/back of the Television, and 30 cm (12 inches) from the top of the television to the wall. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
| 30 cm (12 inches) |
10 cm (4 inches) | 10 cm (4 inches) |
|
CONNECT POWER SWIVEL CABLE
Connect one end of cable (Arrow mark facing left) to the swivel slot of the Plasma Rear Panel. Connect the other end (Arrow mark facing front)to the swivel slot of the Table Top Stand.
TURNING RADIUS
The maximum turning radius is 30˚ (left and right). Do not place any objects on the path of the monitor when using the power swivel feature.
First time use
Caution when moving the main unit
As this product is heavy, whenever it is moved, two people are required to transport it safely. Whenever the unit is moved it should be lifted forward using the top and base on both sides of the Television for stability. When moving the Television, lift the handles (42” models), support the top frame (55” models) and the bottom frame as shown below. Do not grab the speakers or the back cover when lifting.
C
D |
NOTE: The Table Top Stand and Power Swivel cable
for model 55HDS52 are not included (Optional).
42”55”
5