Still Mode
You can pause the image shown on the TV screen.
Press [PAUSE F] to pause the image shown on the TV screen.
FREEZE
•The sound output will not be paused.
•If no signal is detected or protected signal is received during still mode, the image remains paused and the sound output will be muted.
•The still function will be released after 5 minutes.
To cancel still mode, press any button except [POWER y].
Switching Each Input Mode
You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access external devices when they are connected to the unit.
Press [SOURCE] or [CH +] repeatedly to cycle through the input modes.
Source
TV
Video1
Video2
Component
HDMI1
HDMI2
HDMI3
DTV/TV channel
Video1
or
Video2
Component
HDMI1 (or PC input)
HDMI2
HDMI3
•Pressing [CH
Switching Audio Mode | INTRODUCTION | |||||||||||||
| ||||||||||||||
This section describes how to switch the audio in the analog mode and how |
| |||||||||||||
to switch the audio language in the digital mode. |
| |||||||||||||
| TV |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Press [SAP] to display the currently selected audio |
| PREPARATION | ||||||||||||
mode. While receiving an MTS broadcast, press |
| |||||||||||||
|
| |||||||||||||
repeatedly to cycle through the available audio |
|
| ||||||||||||
channel. |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 11 |
|
|
|
|
|
| |||
|
|
|
|
| SAP / STEREO |
|
|
|
|
| ||||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When all audio are available | WATCHING | |||||||||||||
| ||||||||||||||
| SAP / STEREO |
|
| SAP / MONO |
| |||||||||
|
| |||||||||||||
|
|
|
| SAP / STEREO |
|
|
| TV | ||||||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| ||||||
When stereo and monaural audio are available | ||||||||||||||
| ||||||||||||||
| MONO / STEREO |
|
| MONO / STEREO |
| |||||||||
|
|
|
| |||||||||||
|
| OPTIONAL | ||||||||||||
| SAP / MONO |
|
| SAP / MONO | ||||||||||
When SAP and monaural audio are available |
| |||||||||||||
|
|
|
|
|
|
|
|
| SETTING | |||||
|
|
|
| MONO | ||||||||||
When only monaural audio is available |
| |||||||||||||
|
|
|
| (cannot be switched) |
| |||||||||
|
|
|
|
| ||||||||||
MONO | OPERATING | |||||||||||||
: Outputs | ||||||||||||||
STEREO | : Outputs |
| ||||||||||||
SAP | : Outputs second audio program |
| ||||||||||||
DTV |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||
1 Press [SAP] to display the currently selected language |
| |||||||||||||
and the number of available languages. | ||||||||||||||
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| 11.1 |
|
|
|
|
| SETTING | |||
|
|
|
|
|
| English 1/3 |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
2 Press [SAP] repeatedly to cycle through the available |
| |||||||||||||
| ||||||||||||||
TROUBLESHOOTING | ||||||||||||||
audio languages. |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| ||||||
• Available languages differ depending on the |
| |||||||||||||
| broadcast. “Other” is displayed when the audio |
| ||||||||||||
| language cannot be acquired, or the acquired |
| ||||||||||||
| ||||||||||||||
| languages are other than English, Spanish or French. | INFORMATION | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Note: |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||
| • [SAP] does not control external audio devices. |
|
| |||||||||||
| • The information display will automatically disappear in a |
|
| |||||||||||
| few seconds. |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
19
EN