Indicators and Specifications

10Peak(ing) control — The Peaking control affects the sharpness of the picture on the RGB output. Increased peaking can compensate for detail (mid- and high-frequency) loss from low bandwidth system components or capacitance in long cables. The minimum setting (at the counterclockwise limit) provides no peaking. The maximum setting (at the clockwise limit) provides 100% peaking. Adjust this control while viewing the displayed image to obtain the optimum picture sharpness.

Peaking has no affect on the DVI output of the Buffered Loop- through connector.

Operation

After the DVI-RGB 100 and its connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly.

The computer reads the DDC on power up to determine the direct digital video resolution and refresh rate to output. Ensure that the local DVI monitor and the RGBHV monitor can both display the selected resolution and refresh rate, otherwise images may be distorted or missing.

Ensure that the computer and local DVI monitor are connected to the DVI-RGB 100, and the DVI-RGB 100 and local monitor have power applied, before applying power to the computer. If the other devices are not turned on before the computer is, the image will not appear.

DVI Connector Pin Assignments

Figure 5 and the table below define the DVI pin assignments.

	1	8	8	1

9	17	24	24	17

	Female Connector
			Male Connector

Figure 5 — DVI connectors

DVI/DFP signals run at a very high frequency and are especially prone to bad video connections, too many adapters, or excessive cable length. To avoid the loss of an image or jitter, follow these guidelines:

•Do not exceed 16.4 feet (5 meters) on the input or buffered loop- through of the converter.

The missing connectors on the included DVI cable are not required for the single link of DVI-D data supported by the DVI-RGB 100. These pins are grayed out on the following table.

Pin	Signal	Pin	Signal	Pin	Signal

1	TMDS Data 2-	9	TMDS Data 1-	17	TMDS Data 0-

2	TMDS Data 2+	10	TMDS Data 1+	18	TMDS Data 0+

3	TMDS Data 2/4	11	TMDS Data 1/3	19	TMDS Data 0/5
3	Shield	11	Shield	19	Shield
	Shield		Shield		Shield

4	TMDS Data 4-	12	TMDS Data 3-	20	TMDS Data 5-

5	TMDS Data 4+	13	TMDS Data 3+	21	TMDS Data 5+

6	DDC Clock	14	+5 V Power	22	TMDS Clock
6	DDC Clock	14	+5 V Power	22	Shield
					Shield

7	DDC Data	15	Ground (+5 V)	23	TMDS Clock+

8	No Connection	16	Hot Plug Detect	24	TMDS Clock-

•Use only the cable designed for DVI signals supplied by Extron.

•Limit or avoid the use of adapters.

•Use only approved DVI/DFP connectors.

CAUTION Use only cables specifically intended for DVI or DFP interfaces. Use of non-DVI or non-DFP cables or modified cables can cause the DVI-RGB 100 to fail.

Specifications

Video

Bit rate (pixel bandwidth)	1.6 gigabits/second/color
Pixel data bit depth	24 bit
Control data bit depth	6 bit
Maximum resolutions	1280 x 1024 at 85 Hz, 1600 x 1200 at 60 Hz

Video input

Number/signal type	1 DVI-D digital video
Connectors	1 DVI-D female (DVI input)
	1 DVI-D female (DVI loop through)
Minimum/maximum levels	0.5V to 1.0V p-p
Impedance	50 ohms
Maximum DC offset	±0.5V

Video output

Number/signal type	1 RGBHV, RGBS, RGsB
Connectors	6 BNC female

DVI-RGB 100 • Operation

DVI-RGB 100 specifications

Extron Electronics is renowned for its cutting-edge solutions in audiovisual technology, and the DVI-RGB 100 stands out as a high-performance interface for video signal distribution. This device is particularly designed for converting DVI and RGB signals, making it an essential component in various multimedia systems, including those utilized in educational institutions, corporate environments, and professional AV setups.

One of the distinguishing features of the DVI-RGB 100 is its ability to provide seamless signal conversion between DVI and analog RGB, supporting resolutions up to 1920x1200 at 60 Hz. This ensures that users can enjoy high-definition video content without any degradation in image quality. The device supports a broad range of input formats, enhancing its versatility in various applications.

A key technological advancement embedded in the DVI-RGB 100 is its advanced signal processing capabilities. The device features Extron's proprietary technology to optimize video signals, ensuring minimal signal loss and maximum fidelity. Its built-in signal conditioning compensates for the effects of cable length, allowing for long-distance transmission without compromising quality.

The DVI-RGB 100 is engineered with simple plug-and-play functionality, allowing for quick installation and ease of use. Users can connect their devices without the need for complicated configurations, significantly reducing setup time and facilitating a user-friendly experience. Additionally, it includes an LED indicator that provides real-time feedback on signal status, ensuring users can quickly identify any issues.

Another important characteristic of the DVI-RGB 100 is that it offers extensive compatibility with a broad range of devices, including computers, projectors, and monitors. It is equipped with DVI and 15-pin VGA connectors, providing flexibility in adapting to different system requirements.

In terms of design, the DVI-RGB 100 is compact, allowing for easy integration into rack-mounted systems or desktop setups. Extron’s commitment to quality is evident in this product, as it is built to withstand the demands of professional AV environments while ensuring reliability and durability throughout its lifecycle.

With its combination of high-quality signal conversion capabilities, user-friendly design, and robust performance, the Extron DVI-RGB 100 stands as a reliable solution for achieving exceptional video quality in a variety of settings. It is an indispensable tool for anyone looking to optimize their audiovisual experiences.