Fostex D2424LVMKII manual Undo and redo recording single undo/redo

Model D2424LVmkII Quick Operation Guide

Undo and redo recording (single undo/redo)

Everybody makes mistakes. If you make a mistake in recording, you can restore and re-do the data that existed before the mistake occurred. These functions are called “Undo” and “Redo ,” and are executed by the [UNDO/REDO] key on the control panel.

The Undo function enables you to cancel the latest recording or edit and restore the previous state. Using the Redo function after using the Undo function enables you to cancel the Uno operation and restore the latest recording or edit. These functions have some limitations as described in the <Note> below.

As described earlier in "Formatting a new disk", if you format the disk with the multiple undo function ON, "multiple undo" is possible. See "Multiple undo function" in the Reference manual.

After recording		Recorded area
	Undo	Redo
Before recording

<Note>

You can repeatedly use the Undo/Redo functions until you perform one of the following operations:

•You make a new recording.

•You perform a new edit (Copy/Paste, Move/Paste, Auto Punch in/out, Erase, etc.).

•You turn off the power to the recorder.

•You select a different Program.

•You execute the Multiple Undo operation.

AUTO RTN				AUTO RTN
AUTO PLAY	CLIPBOARD			AUTO PUNCH			PGM SEL	EXIT/NO	EXECUTE/YES
	IN	OUT	START	IN	OUT	END
			PREVIEW					EJECT	CHASE
					CHARACTER			LOCATE MEMORY
	EDIT		SETUP	UNDO/REDO	PREV	NEXT	DISP SEL	STORE	RECALL

SHIFT	TC READY	TC GEN	M.UNDO	PREV TC NEXT TC	TIME BASE SEL	HOLD
AUTO	REHEARSAL		LOCATE	VARI PITCH
PUNCH
	TAKE
				P.EDIT
RECORD	STOP	PLAY	REW	F FWD
ALL READY
	CLIPBOARD PLAY
	LOCATE ABS 0
	LOCATE REC END
		1, 2 ([UNDO/REDO] key)

1.After making a recording (or playing back a newly recorded data), press the [UNDO/REDO] key.

The recorder displays “Undo!”, then “COMPLETED !”, and displays the previous Time Base indication. Undoing the recording will restore the status obtained before recording.

COMPLETED!

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

2.To cancel the undo operation, press the [UNDO/REDO] key again.

The recorder displays “Redo!”, then “COMPLETED !”, and displays the previous Time Base indication.

Performing the Redo operation will cancel the Undo operation and restore the state obtained after recording.

COMPLETED!

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

<Hints>

The single undo/redo function executes undo/ redo operation only against the latest take.

The "multiple undo function" can execute undo against all takes after the current disk had been formatted. When the multiple undo function is set to ON, the recorder stores all takes automati- cally and can recall the desired take (undo) if necessary.

<Cautions for the multiple undo function>

•Multiple undo is possible only when the current disk is formatted with the "Multiple undo function" ON.

•A disk formatted with the multiple undo function ON has more information stored on it more than a disk formatted with the multiple undo function OFF.

•With the single undo/redo function described above, the data you undo will be erased when the next recording is done. Therefore, once you execute a single undo, the undone take cannot be restored even if you execute multiple undo later.

* Refer to the Reference manual for details.

17