Model D2424LVmkII Quick Operation Guide
Mixdown
After overdubbing and
The mixdown signals are usually output from the mixer’s STEREO OUT L/R. Connect the master recorder.
|
| Initialize the recorder. |
|
|
|
|
|
|
|
|
|
1. | Set all tracks to the SAFE status. | 5. | Locate the top of the Program. | ||
2. | Locate the top of the Program on this recorder. | 6. | Start recording on the master recorder. (Take) | ||
3. | Set the master recorder to | 7. | Press the [PLAY] button on this recorder to start | ||
|
|
|
| playing the Program from the beginning. |
4.Play the Program from the beginning and adjust the
recording level on the master recorder while adjusting | 8. | When mixdown is completed, stop the master |
|
the tonal quality and mix balance of the playback | recorder and this recorder. | |
sound from the mixer. (Rehearsal) | ||
|
Adjust the input level on the master recorder so that the STEREO OUT L/R meters on the mixer respond to the same degree as the level meters on the master recorder.
Basic Locate function
The Locate function enables you to locate the desired point (move the current position of the recorder) immediately. There are two locate methods: storing the desired locate point (time or bar/beat/clock value) into the memory keys, and locating the point without storing it.
This section explains “Locating the top of the Program” and “Locating the last recording point in the Program” and do not involve storing locate points. Refer to the Reference Manual for information on storing and locating locate points.
On this recorder, the top of the Program on the disk is called “ABS 0” and the end of the recorded area is called “REC END.” (If the Program has no data recorded, ABS 0 corresponds to REC END.) You can use this function to locate the ABS 0 or REC END point immediately, regardless of the current recorder position.
ABS 0 | REC END |
Recorded Area
LOCATE ABS 0
LOSATE REC END
Current Position
• Locating the top of the Program
You can immediately move to the top of the Program (ABS 0), regardless of the current position of the Program.
1.Press and hold down the [STOP] button, and press the [REWIND] button.
|
|
|
| [STOP] button |
|
|
| [REWIND] button | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•Locating the end of the recorded area of the Program
You can immediately move to the end of the recorded area of the Program, regardless of the current position of the Program.
1.Hold down the [STOP] button and press the [F FWD] button.
|
|
|
| [STOP] button |
|
|
|
|
|
| [F FWD] button | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
21