Bowers & Wilkins CT800 Important Safety Instructions, Explanation of Graphical Symbols

Page 4

IMPORTANT SAFETY INSTRUCTIONS

The CT8 XO active crossover is a powered device. Before use, please read and heed the following instructions:

Caution:

To reduce the risk of electric shock, do not dismantle the apparatus and do not expose the apparatus to rain or moisture. No user-serviceable parts inside. Refer servicing to qualified personnel.

Explanation of Graphical Symbols

The lightning flash within an equilateral triangle is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNINGS:

1Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Owner’s Manual

8Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

11Only use attachments/accessories specified by the manufacturer.

12

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

 

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus

 

combination to avoid injury from tip-over.

13Unplug this apparatus during lightning storms or when unused for long periods of time.

14Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorised substitutions may result in fire, electric shock or other hazards.

16For continued protection against fire hazard, use fuses only of the correct type and rating. Mains fuses are located inside the casing of the appliance and should be replaced only by an authorised operative.

17Isolation of the appliance from the power supply is by means of either the switch on the rear of the appliance or removal of the power cord from the rear of the appliance or removal of the power cord from the wall power outlet. Either the wall outlet or the rear of the appliance must remain freely accessible at all times while the apparatus is in use.

18This product should be operated only from the type of power source indicated by the marking adjacent to the power cord entry. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

3

Image 4
Contents CT800 Series Table of Contents Limited Warranty WarrantyHow to claim repairs under warranty Important Safety Instructions Explanation of Graphical SymbolsPage Introduction Environmental InformationConcept Page Planning the installation Safety WarningCheck the contents against Figure Planning the installation Speaker Position~60 o Mounting the speakers To take up any rocking. figure Installation into drywall figure Installation to wall surface figure Continue for all cases Speakers Connecting the SystemCT8 DS only CT8 XO Rear Panel CT8 XO crossover/equaliser Description of Controls Description of controlsPage Equipment Required Configure the unit to the gain of each power amplifierConfigure the CT800 XO to the speaker Setting the Subwoofer gain Configure the dipole lobe for a CT8 DSTheory Configure the equalisersProcedure Page Our case the original measurement at position #10 is Rn Page Running In and Ancillary Equipment Ancillary equipmentAftercare Specifications CT8 LRCT8 DS