Vidikron Model 85 manual Installation

Page 56

Installation

Adjusting the Height (Y): With the white field still on-screen, loosen the

Height/Y Adjustment T-Screws on either side of the lens. Then, slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

When the height is properly set, tighten the Height Adjustment T-Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below the

Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Correct Lens Angle

Incorrect Lens Angle

The anamorphic lens will almost always be angled with respect to the projector; this is normal.

Once the proper lens angle has been set, firmly tighten the Pitch Adjustment T-Screws to secure the lens in place.

There may be some pincushion distortion even after the lens is properly

Note adjusted, especially at shorter throw distances. If this is the case, Vidikron recommends that you slightly over-scan the image into the screen frame area to mask the distortion.

44

Vidikron Vision 85 Owner’s Operating Manual

Image 56
Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation ViiiSerial Communications Maintenance and TroubleshootingSpecifications Table of Contents 1List of Figures Vision 85 Main Menu 1080i Digital or 1080p Sources Only About This Manual This ManualUsing This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Vision 85 at a Glance Vision 85 Front/Top/Side/Bottom/Rear ViewVertical Lens Shift Vision 85 Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector VHD Controller Front Panel VHD Controller Front PanelComponent Video RCA connectors VHD Controller Rear PanelHdmi 1 / Hdmi 2 Digital InputsPower Input 100 to 240 VAC Video 1 / S-VIDEOVolt 750 mA Trigger Outputs ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlCursor Buttons On / OFFENT Enter Memory Preset Buttons ISF NT Night CustVideo VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not usedOperation Remote ControlTo install batteries in the remote control Installation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 85/CineWide or Vision 85/CineWideInstallation Considerations Projector Installation OptionsInstallation Type Projector Calibration Digital 1080i or 1080p signalsThrow Ratios for the Vision 85 Series Throw Range Throw RatioProjector Model VisionPosition Ceiling InstallationFloor Installation Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation 85/CineWide Vision 85/CineWide with Lens Base PlateAdjusting the Projection Mounting the VisionFloor Mounting Upright AngleVHD Controller Connector Panel AccessConnections to the Vision 85 and VHD Controller Connecting Source Hdmi Connections See FigureController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure 12. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting a PC or Automation System to the VHD Controller 15. RS-232 Control System ConnectionOutputs to External EquipmentConnecting an External IR Receiver to the VHD Controller 17 -volt Trigger Output Connection from ProjectorTurning on the Power Power sourceAdjusting the Picture Orientation Primary Lens AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation Adjustment Vision 85/CineWideAdjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 85/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 22. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4OperationISF Presets ServiceInput Source Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode ServiceCode Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Picture Adjust Color Temp VAC Iris Lamp PowerLanguage KeyISF Effects of Primary Color Hue Adjustments Picture Adjust AdvancedWhite Balance Options HD/RGB AdjLamp Hours read-onlyRefer to Lamp Hours on Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language settingOperation 5Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Table Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Hdinputres YES Enter keySerial Communications Vision 85 Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron