Vidikron Model 85 manual Typical Test Pattern for Adjusting Sharpness, Input Position

Page 67

Operation

Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5.Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.

Figure 4-5. Typical Test Pattern for Adjusting Sharpness

Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position for the current source.

When you change an input position setting, save the change to a preset

Note afterwards. Otherwise, the change will be lost when a different input is selected. (The input position settings are saved for each input and resolution separately.) For information about saving settings, refer to ISF Presets on page 56.

Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Use the right or up cursor button to shift the image to the right; use the left or down button to shift it to the left.

Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Use the right or up cursor button to shift the image upward; use the left or down button to shift it downward.

Width: Select Width from the Input Position menu to change the projected image width. Use the right or up cursor button to increase the width; use the left or down button to decrease it.

Height: Select Height from the Input Position menu to change the projected image height. Use the right or up cursor button to increase the height; use the left or down button to decrease it.

Overscan: Image Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Input Position

Input Position

Left/Right

Up/Down

Width

Height

Overscan

Vidikron Vision 85 Owner’s Operating Manual

55

Image 67

Contents 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii OperationSpecifications Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures Vision 85 Main Menu 1080i Digital or 1080p Sources Only This Manual About This ManualIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 85 Front/Top/Side/Bottom/Rear View Vision 85 at a GlanceVertical Lens Shift RS-232C Input RJ-11 female connector Wired IR 3.5-mm, mini phono jackVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelInputs Component Video RCA connectorsVHD Controller Rear Panel Hdmi 1 / Hdmi 2 DigitalComLink RS-232 Output Power Input 100 to 240 VACVideo 1 / S-VIDEO Volt 750 mA Trigger OutputsVHD Controller/Vision 85 Remote Control Vision 85 Remote Control UnitENT Enter On / OFFCursor Buttons VID 1 2 / S-VID 2 5 S-Video Memory Preset Buttons ISF NT NightCust VideoNot used Vision 85 Built-In KeypadTo install batteries in the remote control Remote ControlOperation Installation If installing a Vision 85/CineWide or Vision 85/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toProjector Calibration Digital 1080i or 1080p signals Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 85 SeriesThrow Range Throw Ratio Projector ModelFloor Installation Ceiling InstallationPosition Folded Optics Installing the Optional CineWide Lens Mount 6shows the Vision 85/CineWide with AutoScope motor assembly Vision 85 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Vision 85/CineWide with Lens Base Plate 85/CineWideAngle Adjusting the ProjectionMounting the Vision Floor Mounting UprightConnections to the Vision 85 and VHD Controller Connector Panel AccessVHD Controller Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with Connecting SourceHdmi Connections See Figure Controller12. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure15. RS-232 Control System Connection Connecting a PC or Automation System to the VHD ControllerEquipment Outputs to External17 -volt Trigger Output Connection from Projector Connecting an External IR Receiver to the VHD ControllerPower source Turning on the PowerPrimary Lens Adjustments Adjusting the Picture OrientationAnamorphic Lens Installation Adjustment Vision 85/CineWide Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Anamorphic Lens Top View Vision 85/CineWide with AdjustmentAutoScope 22. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry 4Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceInput Source Main MenuAspect Ratio Aspect Ratio Description Aspect Ratio SettingsSurface, eliminating the black bars. PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Service Press Menu to exit test pattern modeCode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Standard VisionOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Key Picture AdjustColor Temp VAC Iris Lamp Power LanguageISF Picture Adjust Advanced Effects of Primary Color Hue AdjustmentsWhite Balance Lamp Hours read-onlyRefer to Lamp Hours on HD/RGB AdjOptions Always set this option to On. Doing otherwise may disrupt Language setting Orientation Refer to Adjusting the Picture Orientation onOperation Lamp Replacement 5Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Table Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Value Description Min/max Stored? CommandBrightness Command Parameter Value Description Min/max Stored? Enter key Hdinputres YESSerial Communications Vision 85 Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron