ViewSonic VS12472 Replacing the Battery, EN-12, For the first time use, For battery change

Page 15

Replacing the Battery

For the first time use:

Remove the transparent insulation tape by pulling it before use.

For battery change:

1.Push the catch to the left and remove the battery holder.

2.Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.

3.Push the battery holder back into the remote control until you feel a click.

Caution

„ Risk of explosion if battery is replaced by an incorrect type.

„Dispose of used batteries according to the instructions.

„Make sure the plus and minus terminals are correctly aligned when loading a battery.

„Keep the battery out of the reach of children.

„Do not recharge the battery or expose the battery to fire or water.

„Do not dispose the used battery along with household waste. Dispose u batteries according to local regulations.

„Danger of explosion may happen if batteries are incorrectly replaced. Replace only with the same type recommended by the manufacturer.

„ Battery should not be in or near to fire or water, keep batteries in a dark and dry place.

„If suspect battery leakage, wipe out the leakage and then replace a new bat the leakage adheres to your body or clothes, rinse well with water immediat

EN-12

Image 15
Contents ViewSonic EN-i Compliance InformationEN-ii Important Safety InstructionsEN-1 Declaration of RoHS ComplianceEN-2 Copyright InformationEN-3 Contents Projector Features IntroductionEN-5 Package Contents Projector Overview Front ViewEN-7 Rear View Bottom ViewEN-8 EN-9 Using the ProductControl Panel Button Function10 12V OUT Connection PortsEN-10 RS-232EN-11 Remote ControlFor the first time use Replacing the BatteryFor battery change EN-12EN-13 Remote Control OperationInstallation Connecting the ProjectorEN-14 EN-15 Powering On/Off the ProjectorPowering On the Projector Powering Off the ProjectorEN-16 Adjusting the ProjectorAdjusting the Projector Height Adjusting the Projector Zoom and FocusDiagonal Adjusting Projection Image SizeEN-17 Screen Screen sizeEN-18 Menu OperationEN-19 How to operate Picture Computer / Video ModeEN-20 Setting Computer / Video Mode EN-21 Computer Image Computer ModeVideo Image Video Mode Sound Computer / Video ModeEN-22 Option Computer / Video Mode Network Config Computer / Video ModeEN-23 Language Computer / Video Mode Factory Default Computer / Video ModeEN-24 There are two ways to connect to the network control Auto IP address setting Dhcp YesNetwork Control PreparationEN-26 User name PasswordEN-27 Manual IP address setting Dhcp NoEN-28 Select Intel Protocol TCP/IP and click Properties„ Click Use the following IP address EN-29 EN-30 Control the projector via a web browserEN-31 Description AdministratorDescription EN-32Status RemarkPicture EN-33Control BasicOption SettingEN-34 Computer ImageNetwork Setting EN-35Network Alert Condition Email SettingEN-36 AlertSchedule EN-37EN-38 Tips for solving web page problemsEN-39 EN-40 MaintenanceCleaning the Lens Cleaning the Projector HousingEN-41 Replacing the LampEN-42 EN-43 SpecificationsLED Indicator Messages AppendixEN-44 Sync Hz Compatibility ModesComputer EN-45Signal Horizontal Frequency kHz Vertical Frequency Hz VideoEN-46 Remote control problems TroubleshootingStart-up problems Image problemsRS-232 Command and Configuration Header Command ResponseEN-48 Wire List EN-49Sub 9 pin IR Control Code EN-50Key Format Byte1 Byte2 Byte3 Byte4 Customer Support Who the warranty protects What the warranty coversLimited Three 3 year General Warranty Limited One 1 year Heavy Usage WarrantyEffect of state law How to get serviceLimitation of implied warranties Exclusion of damagesMexico Limited Warranty Número Gratis DE Asistencia Técnica Para Todo México