Sanyo DP26671, DP36671 Starting setup, TV operation, To select the video input source, Aaa Zzz

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press POWER (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

		TV Location	Store
		Signal Type	Cable
		Automatic Search	Start
		This unit has been preset to STORE brightness
		This setting does not qualify under ENERGY
		STAR. To reduce brightness and energy
		consumption, change setting to ‘HOME’. This
		setting does qualify under ENERGY STAR.
2		:Select	:Adjust
	Press ▲ or ▼ to select “TV Location”, then press
	◀ or ▶ to select “Home” or “Store”. This product
	qualifies for ENERGY STAR In Home mode
	default setting.
	NOTE:
	•	This unit has been preset to STORE brightness.
		This setting does not qualify under ENERGY
		STAR. To reduce brightness and energy
		consumption, change setting to ‘HOME’. This
	•	setting does qualify under ENERGY STAR.
		The device may not conform to the ENERGY
		STAR standard after Reset is performed or the
3		Backlight is adjusted.
	Press ▲ or ▼ to select “Signal Type”, then press
	◀ or ▶ to select “Cable” or “Air”.

4 Press ▲ or ▼ to select “Automatic Search”, then press ▶ or ENTER.

5 Now the “Auto Setup” starts. After the Auto Setup is completed, the TV channel appears on the screen.

•Depending on the reception condition, it may take from 15 minutes to 30 minutes to complete memorizing digital cable channels. Please be patient.

NOTE:

• If you press EXIT in the process of “Auto Setup”, the Auto Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT to see your changes.

TV operation

1 To turn on the TV, press POWER.

(POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or – . The volume level will be indicated on the screen by green bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of green bars also decreases.

Set the Signal Type option to the appropriate
3 position (see “Air/Cable selection” on page 20).
Press the Direct Channel Selection (0-9, –)
4 buttons to select the channel.
(If you press only channel number, channel selection
will be delayed for a few seconds.)							ENGLISH
			select channel 12, press 1, 2, then press
TO SELECT ANALOG CHANNELS
1-9:		Press 1-9 as needed. Example, to select
10-99:		channel 2, press 2, then press ENTER.
		Press the 2 digits in order. Example, to
			ENTER.
100-135: Press the 3 digits in order. Example, to
			select channel 120, press 1, 2, 0, then
			press ENTER.
TO SELECT DIGITAL CHANNELS
Press the first 1-3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1,
then press ENTER.
•	If a channel is selected with only audio content,
•	“Audio only” will be displayed on the screen.
	If a channel is selected with a weak digital signal,
	“Digital channel signal strength is low” will be
	displayed on the screen.
	The same program may be available on either
	an analog channel or a digital channel.You may
•	choose to watch either format.
	If a channel is selected to which you have not
	subscribed, “Digital channel is encrypted” will be
	displayed on the screen.
VHF/UHF/CABLE CHANNELS
	Air				Cable
VHF					VHF
2-13					2-13
UHF				STD/HRC/IRC
14-69			14-36			(A) (W)
			37-59			(AA) (WW)
			60-85			(AAA) (ZZZ)
			86-94		(86) (94)
			95-99			(A-5) (A-1)
			100-135 (100) (135)
			01			(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT SELECT, then press ▲ or ▼ or corresponding Number buttons (0- 7), then press ENTER.You can select TV, Video1, Video2, Component, HDMI1, HDMI2, PC or DVD depending on which input jacks you used to connect your devices.

Input Select

0.TV

1.Video1

2.Video2

3.Component

4.HDMI1

5.HDMI2

6.PC

7.DVD

[0-7]:Select

CH /	/ . The channel
Press and release CH
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on page 20.	17

56Q0221A_eng.indd 17

1/8/11 5:31:55 PM