PC Adj. menu

GB	MENU OPERATION

Setup menu

■PIP/POP Setup

Use the 5 or 6 button to select PIP/POP Setup and press the

1or 2 button to enter the sub menu.

PIP/POP Mode: Using the 1 or 2 button select the most suitable mode PIP1, PIP2, POP or Off. (Please refer to page 12.)

✐When Mode is set to Off, Sub Source and PIP Position will not work.

Main Source is used to select input source (AV1, RGB, AV2, AV3, PC, DVI or Network ) for main picture by using the 1 or 2 button.

Sub Source is used to select input source (AV1, AV2, AV3, PC or DVI ) for sub picture by using the 1 or 2 button.

✐For a combination of main picture and sub picture: only DVI or Network input can assemble with other input source. For example, if main source is selected as AV1 input, then the sub source must be DVI or Network input.

PIP Position: Using the 1 or 2 button it can be selected Top Left, Top Right, Bottom Right or Bottom Left.

■Initial Settings

This function returns all setting values except for Installation Mode.

■Text Language

Use the 5 or 6 button to select Text Language and press the

1or 2 button to select Western, Eastern, Russian, Arabic or

Farsi.

■Tile Mode

This function allows you to split an image to suit your monitor grid format to create a video wall.

Use the 5 or 6 button to select Tile Mode and press the 1

or 2 button to enter the sub menu as follows.

Tile Mode Active can be set On or Off using the 1 or 2 button.

H_Sets

V_Sets

H_Sets is used to divide the horizonal picture into more than one part, but the most is 5 parts (5 monitors).

V_Sets is used to divide the vertical picture into more than one part, and the most is also 5 parts (5 monitors). Using the 1 or 2

button to set.

H Location is used to select one part of the horizonal picture to

display on the current LCD Monitor using the 1 or 2 button.

V Location is used to select one part of the vertical picture to display on the current LCD Monitor using the 1 or 2 button.

Bezel H Adjustment is used to align the image horizontally with

respect to the other monitors in the video wall to accomodate the bezel width using the 1 or 2 button. (0~10)

Bezel V Adjustment is used to align the image vertically with respect to the other monitors in the video wall to accomodate the

bezel width using the 1 or 2 button. (0~10)

■AV2 Setting

Use the 5 or 6 button to select AV2 Setting and press the

1or 2 button to select YPbPr or RGBHV.

Connect your PC to either PC-IN or RGBHV on the rear of the set. Once connected select PC mode or AV2 (RGBHV, see page 5 for AV2 input settings) via the INPUT button on your remote control. The set will become a monitor for the PC.

■Native Resolution

Use the 5 or 6 button to select Native Resolution and press the 1 or 2 button to select XGA or WXGA 1366 x 768.

■PC Power Save

Use the 5 or 6 button to select PC Power Save and press the

1or 2 button to select ON or OFF.

Press the MENU button and select PC Adj. using the 5 or 6 buttons, press the 1 or 2 button to enter. Press the BACK button to return to the previous menu. Press the MENU button to exit menu operation.

Auto Adjust is used to automatically detect incoming signal, and adjust itself to optimize its performance by using the 1 or 2 button. If the image is not displayed properly, a manual adjustment is required (Refer to following adjustments).

H-Positionis used to move the horizontal picture position by using the 1 or 2 button.

V-Positionis used to move the vertical picture position by using the

1or 2 button.

Clock is used to eliminate flicker from the image by using the 1 or 2 button.

Phase is used to eliminate disorder from the image by using the 1 or 2 button.

MENU OPERATION