External Control Device Setup
*All data are transmitted by Hexadecimal code
*Two/One part Channel: 6th bit
This bit is used in a
*Using physical channel: 5th bit
If the channel band is NTSC air or NTSC cable, channel tun- ing can be done by only physical channel. In this case, using physical channel bit must be low(0).
But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable.
If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1).
Example)
1. Analog channel: NTSC cable, channel number(35), main
picture Command: ma 00 23 xx xx xx xx 01 attribute(0x01): main picture, two part(it’s not mandatory), using physical chan- nel, NTSC cable ‘xx’ data: don’t care major and minor channel number in case analog channel tuning.
2. Digital channel: ATSC air, channel number(don’t know phys- ical channel, major(30), minor(3)), sub picture
Command: ma 00 xx 00 1E 00 03 A2 attribute(0xA2): sub pic- ture, two part, not using physical channel, ATSC air ‘xx’ data: don’t care analog channel number in case digital channel tun- ing.
3. Digital channel: ATSC air, channel number(physical(20),major(20), minor(3)), sub picture Command: ma 00 14 00 14 00 03 82 attribute(0x82): sub pic- ture, two part, using physical channel, ATSC air.
Acknowledgement
[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][Data5][x] [a][ ][Set ID][ ][NG][Data0][x]
23. Channel Add/Del (Command: m b)
G To add and delete the channels
Transmission
[m][b][ ][Set ID][ ][Data][Cr]
Data 0: Channel Delete
1: Channel Add
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x]
25. Input select(Command: x b) (Main Picture Input)
G To select input source for TV.
Transmission
[x][b][][Set ID][][Data][Cr]
Data Structure
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| DATA(Hex) |
|
|
|
| INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
00 |
|
|
| DTV (Antenna) | ||||||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |||||
01 |
|
|
| DTV (Cable) | ||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
10 |
|
|
|
|
|
| ||||||
|
|
| Analog (Antenna) | |||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
11 |
|
|
|
|
| |||||||
|
|
| Analog (Cable) | |||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
20 |
|
|
| Video | ||||||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
21 |
|
|
| Front Video | ||||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
40 |
|
|
| Component 1 | ||||||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
41 |
|
|
| Component 2 | ||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
50 |
|
|
| RGB DTV | ||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
60 |
|
|
| RGB PC | ||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| |||||||
90 |
|
|
| HDMI/DVI | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
24. Key (Command: m c)
G To send IR remote key code Transmission
[m][c][ ][Set ID][ ][Data][ ][Cr]
Data Key code: Refer to page 51. Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 49 |