Radio Shack DVD / VCR owner manual Quick Use Guide, Connections

✄

1Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4).

6)Press [STOP C] to stop playback.

2	Installing the Batteries
	for the Remote Control
1	2	3

3VCR/DVD Switching

OPEN/CLOSE

POWER SPEED AUDIO /EJECT

	1	2	3
				SKIP/CH.
	4	5	6
VCR button				VCR/TV
	7	8	9
				SLOW
		0	+10
	DISPLAY	VCR	DVD	PAUSE
DVD button
		PLAY
VCR OUTPUT light		STOP
	REC/OTR
VCR OUTPUT DVD	MENU		ENTER
	SETUP	TOP MENU		RETURN
DVD OUTPUT light
	MODE	ZOOM	SEARCH	CLEAR/
			MODE	C. RESET
	SUBTITLE	ANGLE	REPEAT	A-B
	T-SET

OUTPUT button

Quick Use Guide

4Turn on the unit for the first time

VCR

VCR

1

Turn on the TV and set it to channel 3.

•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.

2	POWER	Remote Control TV Screen
		LANGUAGE SELECT
		B ENGLISH	[ON]
		FRANCAIS

or ESPAÑOL

3	CH 01
	AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES

Yes Press [MENU]

to exit.

NO

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memo- rized in this unit by using

[SKIP/CH. G/K H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

2		CLOCK SET
or	MONTH DAY		YEAR
	1 0	/ – –	– – – –
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current month.
3		CLOCK SET
	MONTH DAY		YEAR
or	1 0	/ 0 2	– – – –
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current day.
4		CLOCK SET
or	MONTH DAY		YEAR
	1 0	/ 0 2	2 0 0 6
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current year.
5		CLOCK SET
or	MONTH DAY		YEAR
	1 0	/ 0 2 MON 2 0 0 6
	HOUR MINUTE		AM/PM
	0 5	: – –	– –
	Select the current hour.
6		CLOCK SET
or	MONTH DAY		YEAR
	1 0	/ 0 2 MON 2 0 0 6
	HOUR MINUTE		AM/PM
	0 5	: 4 0	– –
	Select the current minute.

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR OUTPUT light is lit.)

5Clock Setup

VCR

VCR

7	CLOCK SET
MONTH DAY		YEAR
1 0	/ 0 2 MON 2 0 0 6
or
HOUR MINUTE		AM/PM
0 5	: 4 0	P M AM
		B PM

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD OUTPUT light is lit.)

Hint

•Pressing only [OUTPUT] on the front panel DOES NOT switch the mode of the remote control. You MUST select the cor- rect mode on the remote control.

1MENU

or

- M E N U -

TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP

BCLOCK SET LANGUAGE SELECT AUDIO OUT

TV STEREO [ON]

SAP

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2).

Select “AM” or “PM”.

8To exit the CLOCK SET screen

– 27 – EN