Precautions, Power | Eiki 8080 specs

Precautions

1.Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the per- mission of the copyright holder.

2.AC Fuse—The AC fuse inside the unit is not user-service- able. If you cannot turn on the unit, contact your dealer.

3.Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical sol- vents, because they may damage the ﬁnish or remove the panel lettering.

4.Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CARE- FULLY.

AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Plug Cord into a properly ground wall outlet. The three- prong plug should be used without a two-prong adapter whenever possible.

5.Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6.Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your dealer.

7.Handling Notes

•If you need to transport this unit, use the original pack- aging to pack it how it was when you originally bought it.

•Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

•This unit’s top and rear panels may get warm after pro- longed use. This is normal.

•If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

•When you’ve ﬁnished using this unit, remove CD, cas- sette tape, USB ﬂash drive and turn off the power.

8.Installing this Unit

•Install this unit in a well-ventilated location.

•Ensure that there’s adequate ventilation all around this unit, especially if it’s installed in an audio rack. If the ventilation is inadequate, the unit may overheat, leading to malfunction.

•Do not expose this unit to direct sunlight or heat sources, because its internal temperature may rise, short- ening the life of the optical pickup.

•Avoid damp and dusty places, and places subject to vibrations from loudspeakers. Never put the unit on top of, or directly above a loudspeaker.

•Install this unit horizontally. Never use it on its side or on a sloping surface, because it may cause a malfunction.

9.Moisture Condensation

Moisture condensation may damage this unit. Read the following carefully:

Moisture may condense on the lens of the optical pickup, one of the most important parts inside this unit.

•Moisture condensation can occur in the following situa- tions:

–The unit is moved from a cold place to a warm place.

–A heater is turned on, or cold air from an air condi- tioner is hitting the unit.

–In the summer, when this unit is moved from an air conditioned room to a hot and humid place.

–The unit is used in a humid place.

•Do not use this unit when there’s the possibility of mois- ture condensation occurring. Doing so may damage your discs and certain parts inside this unit.

If condensation does occur, remove CD, cassette tape, USB ﬂash drive and leave this unit turned on for two to three hours. By this time, the unit will have warmed up and any condensation will have evaporated.

10.Rated label

Rated label and caution marking are located on the bottom of this unit.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion.

This equipment generates, uses and can radiate radio fre- quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COM- PLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

8080 specifications

The Eiki 8080 is a remarkable projector that has garnered attention for its blend of advanced technology and user-friendly features. Designed primarily for professional and educational environments, it offers a robust solution for presentations, film screenings, and various multimedia applications.

One of the standout features of the Eiki 8080 is its impressive brightness, which typically measures around 3500 lumens. This high luminosity ensures vivid and clear projections even in well-lit rooms, making it a versatile choice for diverse settings. The projector employs state-of-the-art DLP (Digital Light Processing) technology, allowing for superior image quality with sharp details and vibrant colors. This technology also contributes to reduced maintenance requirements and increased lifespan.

In terms of resolution, the Eiki 8080 boasts native XGA (1024x768) resolution, which is ideal for a wide range of content—from detailed slideshows to high-definition videos. The projector supports various aspect ratios, providing flexibility depending on the source material and screen configuration. Additionally, its ability to handle multiple input formats, including HDMI, VGA, and composite video, allows seamless connectivity with different devices such as laptops, Blu-ray players, and cameras.

Portability is another key characteristic of the Eiki 8080. Its relatively lightweight design coupled with an integrated carrying handle makes it easy to transport, making it suitable for traveling professionals or educational setups that require mobility. The projector also features built-in speakers, providing satisfactory audio output for smaller gatherings, although external speakers can be connected for larger audiences.

A user-friendly interface enhances the experience, with straightforward controls that enable quick adjustments to settings such as focus, zoom, and keystone correction. This level of customization allows users to achieve the perfect image alignment and quality, ensuring effective communication during presentations.

Additionally, the Eiki 8080 emphasizes eco-friendliness with energy-saving features, prolonging lamp life and reducing power consumption, which is a crucial consideration for institutions conscious of operational costs and environmental impact. Overall, the Eiki 8080 amalgamates advanced technology, portability, and user-centric design, making it a preferred choice for professionals in various fields.