Winegard RD-4600, RD-4646 owner manual Maintenance, Mount Lubrication, Lubricating Rubber Quad Ring

Page 8

MAINTENANCE

MOUNT LUBRICATION

To lubricate the mount, apply a liberal amount of silicone spray lubricant to the elevating gear, the lubricant hole and between the gear housing and baseplate. Run the antenna up/down and rotate the antenna to distribute the lubricant. See Figure 6.

Spray lubricant

here on elevation gear

Remove cap and spray lubricant into the lubricate hole. Be sure place cap firmly back on.

Spray lubricant around edges

FIGURE 6

LUBRICATING RUBBER QUAD RING

Lubricate rubber quad ring on elevating shaft which is below worm gear with silicone spray lubricant at least twice yearly (Figure 8). This will keep quad ring from becoming brittle which could result in leaks down elevating shaft.

WAVE WASHER

FLAT WASHER

ELEVATING SHAFT

 

WORM GEAR

 

FIGURE 7

LOWER BEARING SURFACE

RUBBER QUAD RING

 

 

 

ELEVATING SHAFT & WORM GEAR ASSEMBLY REPLACEMENT PROCEDURE

NOTE: It is not necessary to remove rotating gear housing from base plate or remove antenna from roof to replace the shaft & worm gear assembly.

STEP 1. Lower antenna to travel position. Loosen screw on elevating crank, remove crank, spring, directional handle. Parts list page 12.

STEP 2. Remove hex nuts, cable clip, and washer from bolt holding elevating tube in rotating gear housing and remove bolt. Parts list page 10.

STEP 3. Remove plastic plug from top of rotating gear housing, disengage elevating gear, remove elevating shaft assembly. Parts list page 10.

STEP 4. Lubricate worm gear assembly on new elevating shaft assembly with spray silicone lubricant. Make sure wave washer, flat washer and quad ring are on lower bearing (Figure 7) and insert assembly in housing.

STEP 5. Reinstall plastic plug in top of housing. Gears will mesh automatically once elevating crank is turned.

STEP 6. Reinstall bolt, hex nuts, cable clip and washers that hold elevating tube in rotating gear housing.

STEP 7. Replace directional handle, spring and elevating crank. Make sure set screw contacts flat surface on shaft before tightening.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation Instructions Install Point Base Toward Front VehicleInstallation & Assembly Antenna closer than 10 from edge of roofAttach reflector to backup assembly as shown in Figure Inside RV Approximately Degrees from Travel Position Directional HandleTravel Position Point toOperation Elevation Turns CCWPosition Except Travel Position Tuning Antenna for Best PictureLowering Antenna to Travel Position Maintenance Elevating Shaft & Worm Gear Assembly Replacement ProcedureMount Lubrication Lubricating Rubber Quad RingOrdering Repair Parts Trouble ShootingWarranty Repair Work Parts List Rear ViewLnbf Interior Hardware KIT Specifications Antenna & MountANTENNA/LIFT/LNBF TWO Year Limited Warranty Roof Template Goes Here
Related manuals
Manual 16 pages 30.92 Kb

RD-4646, RD-4600 specifications

The Winegard RD-4646 and RD-4600 are advanced high-gain satellite antennas designed for consumers and mobile users who demand exceptional performance and reliability in a compact form factor. These antennas are engineered to provide a strong signal reception across a wide range of frequencies, making them suitable for various applications, including RVs, boats, and stationary installations.

The Winegard RD-4646 boasts a significant gain level, which allows it to capture signals from satellites located at greater distances. This is particularly advantageous for users in remote locations or areas with challenging terrain. The RD-4646 features a robust construction and a sleek design, ensuring durability while maintaining an elegant appearance. With its 360-degree reception capabilities, this model eliminates the need for manual adjustments and enhances user convenience.

On the other hand, the Winegard RD-4600 is engineered for versatility and ease of use. It features a compact design, making it suitable for smaller setups while still delivering solid signal performance. The RD-4600 is equipped with automatic satellite acquisition technology, allowing users to lock onto satellites with minimal effort. This feature is especially beneficial for mobile users who frequently change locations, as it drastically reduces setup time.

Both antennas come with a weather-resistant finish, protecting them from harsh environmental conditions, which is crucial for outdoor applications. The RD-4646 and RD-4600 employ advanced materials and innovative construction techniques, ensuring they can withstand extreme weather while maintaining signal integrity.

Another significant feature of the Winegard RD series is their compatibility with various satellite services, including Directv and Dish Network. This versatility ensures that users can choose the service provider that best fits their needs without worrying about compatibility issues.

In conclusion, the Winegard RD-4646 and RD-4600 are exceptional choices for satellite antenna systems. Their advanced technologies, robust features, and user-friendly designs make them suitable for a variety of applications, from mobile users to stationary setups. With their ability to receive strong signals in challenging environments, these antennas represent a solid investment for anyone seeking reliable satellite communication. Whether you are an RV enthusiast, a boater, or someone looking to enhance their satellite reception at home, the RD-4646 and RD-4600 will exceed your expectations.
Top Page Image Contents