Mount Assembly

ASSEMBLY

STEP 1. Position legs and mount pipe as shown in Figure 1.

FIGURE 1

MOUNT PIPE

LEGS (SHORT ENDS)

STEP 2. Attach mount pipe and legs using (2) 1/4” flat washers, (2) 1/4” nylon washers, (1) 1/4” nylock nut, and

(1)3-1/2” hex head cap screw. Insert the screw through the top left hole of leg as shown in Figure 2. Insert wash- ers and install nylock nut. Tighten using (2) 7/16” wrenches.

FIGURE 2

MOUNT PIPE

HAIR SPRING

COTTER

1/4-20

NYLOCK

HEX NUT

		1/4-20 x 3-1/2”
		HEX HEAD CAP SCREW
1/4” FLAT			3-1/2” x 1/4”
WASHER	1/4” NYLON	1/4” FLAT	CLEVIS PIN
	WASHER	WASHER

STEP 3. Insert 3-1/2” clevis pin into the top-right hole of the leg as shown in Figure 2. Secure with hair spring cot- ter.

MOUNT PIPE/DISH BRACKET ASSEMBLY

STEP 4. Line up long bolt inside dish bracket assembly (Figure 4) with the slots on top of the mount pipe.

STEP 5. Secure dish bracket assembly to mount pipe with (2) 1/4-20 x 1” carriage bolts, (2) 1/4” flat washers, and (2) 1/4-20 flanged hex nuts. See Figure 3.

	1/4”	FLAT WASHER
FIGURE 3		1/4-20 HEX NUT
		1/4-20 HEX NUT
		2-1/2”


		HEX BOLT
		DISH BRACKET
		ASSEMBLY

REFLECTOR

BOLT

		1/4-20
		LOCKING KNOB
	1/4” FLAT WASHER	1/4-20 HEX NUT
	1/4-20	1/4” FLAT WASHER
	1/4-20
	HEX NUT
		1/4-20
		HEX NUT
	2.5” CARRIAGE	LOCKING KNOB
	BOLTS	LOCKING KNOB
	BOLTS
	FIGURE 4	DISH BRACKET ASSEMBLY

STEP 7. Install (1) 1/2” carriage bolt into inside hole of clamp bracket (side opposite of numbers on dish bracket assembly) and secure with 1/4” washer and nut.

Install (1) 1/2” carriage bolt into inside hole of clamp bracket (side with numbers on dish bracket assembly). Insert washer over 1/2” bolt and secure with 1/4-20 lock- ing knob.

NOTE: Stud should be facing outward. For both 1/2” bolts.

DISH ASSEMBLY

STEP 8. Attach reflector using (4) reflector bolts, (4) 1/4” flat washers, (4) 1/4-20 hex nuts. See Figure 4.

LNBF/FEED TUBE ASSEMBLY (See Figure 5 for steps 9-13)

STEP 9. Feed 5’ coax through feed tube and attach to LNBF.

STEP 10. Make sure the square hole is facing up on the feed tube, then attach LNBF to the feed tube using (1) 8- 32 x 1-1/4” carriage bolt and using (1) 8-32 hex nut. Tighten enough so that the LNBF is secure.

STEP 11. Insert (2) 1/4-20 x 2.5” carriage bolts (opposite directions) into the bottom two holes of the dish bracket assembly. Insert a washer and a locking knob onto each threaded bolt. DO NOT tighten at this time.

STEP 12. Slide feed tube onto carriage bolts and tighten locking knobs.

STEP 13. Attach splicing connector to 5’ cable and then attach 20’ coaxial cable to splicer. 20’ coaxial cable at- taches to “SATELLITE IN” on receiver.

8-32 x 1.25”

MOUNT PIPE

CLAMP BRACKET

1/2”

HEX BOLT

CARRIAGE

BOLT

8-32

STEP 6. Insert 2-1/2” hex bolt from inside dish bracket out through hole on top of dish bracket assembly. Secure with (1) 1/4” flat washer, (1) 1/4-20 hex nut, and 1/4-20 locking knob. NOTE: The locking knob is used to secure the feed tube when in the storage position.

HEX NUT

FEED TUBE

FIGURE 5

CARRIAGE BOLTS