Memorex Tek Partner Universal Remote Control user manual Magic Search Codes TV 990 VCR 992 CBL

Page 2

1.Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status indicator (located to the left of the "1" button) lights up.

2.Press a desired Device Mode Button (e.g. "TV").

3.Use the number buttons to enter your 3-digit Device Code (from the Device Code List) for your TV. The indicator should go out immediately. NOTE: The status indicator will not blink while entering Device Codes in step 3 above.

4.Turn on your device (e.g. TV), try the functions on the TEK PARTNERTM. If your device (e.g. TV) responds to your requested function correctly, you have entered the correct Device Code. Otherwise, repeat the above setup instructions with the remaining Device Codes until your device (e.g. TV) responds to your requested function.

5.Simply repeat the above procedures to enter the Device Codes for your VCR & CBL - (Remember to press a correct Device Mode Button in step 2 above).

NOTES:

Any Device Codes can be entered into "CBL" & "AUX" modes. (i.e. The "CBL" & "AUX" modes can be used to control TVs and/or VCRs). Simply press the "CBL" or "AUX" Device Mode Button in step 2 above and enter your 3-digit Device Code for CBL or other devices.

If the indicator flashes twice during the above procedure, a wrong Device Code has been entered. You are required to repeat steps 2 and 3 again.

If you cannot find a correct Device Code for your equipment, see Setup by SEARCH THROUGH THE LIBRARY section.

It is highly recommended, for future reference, to write down your Device Codes on the bottom label of your TEK PARTNERTM.

SEARCH THROUGH THE LIBRARY

If you cannot identify a correct Device Code for your equipment from the Device Code List, you may try the code search method.

For example: Turn on your device (e.g. TV).

1.Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status indicator lights up.

2.Press a desired Device Mode Button (e.g. "TV").

3.Enter a following corresponding Magic Search Code, and your TEK PARTNERTM is now ready to start searching.

Magic Search Codes: TV: 990 VCR: 992 CBL: 994

For example, press... ("PREV CH" & "ENTER" ... "TV" ... 990)

To search: Aim your TEK PARTNERTM at the device (e.g. TV), press the "PWR" and

4."VOL+" button alternately, repeatedly, slowly and patiently until the device turns off. (NOTE: There are approximately 70 TV codes, 55 VCR codes, and 55 Cablebox

5.codes.) Once your device has been turned off, immediately press the same Device Mode Button (e.g. TV) again to lock in the code and the indicator should go out. If the indicator flashes twice after pressing the "VOL+" Button, you are already at the last code of the library. You may press "VOL-" to search backward and repeat carefully the above procedures to search again. Simply repeat the above procedures to search the Device Codes for your VCR and CBL keys. (Remember to press a correct Device Mode Button in step 2 above).

Image 2
Contents HOW to Install the Batteries Main Features Setting UP Your TEK PartnertmMagic Search Codes TV 990 VCR 992 CBL Search Through the LibraryOperating the TEK Partnertm Normal Operation MaintenanceTrouble Shooting Punch ThroughTV Brands SpecificationsDevice Code List CraigLloytron Lodgenet Logik Logix Electrohome 160Infinity Mitsubishi Unified LuxmanMemorex NEC UnifiedThomson Proscan Sony Unified Sounddesign 080Techwood Totevision Universal 040 VidtechVCR Brands Graetz Harman Kardon Ferguson FinluxFunai Instant ReplaySaisho Salora MinoltaMultitech National Telefunken Thomson Thorn Sony VIDEO8Symphonic Tashico Tatung Totevision 022Zenith Beta Zenith Unified Cable Box BrandsUnitech Vector Research 212 292 Video Concepts Videosonic Anvision Cablestar DiamondPanasonic 334 Paragon Zenith United Cable United Satellite Videoway