Basic Operation

NORMAL MODE

(When operating Marantz AV equipment products) This remote controller is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER 1, TUNER 2, CD, CD-R, TAPE (tape deck), AUX1 and AUX2.

Learning is not necessary for Marantz products. You can use these products without setting any codes.

1. Press the SOURCE button. For this example, press DVD.

Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed.

To change the ampliﬁer on other source, press the SOURCE button twice (double-click). The code is sent, and then the ampliﬁ er source changes to DVD.

SETTING THE BACK LIGHT

Each time press the buttons, illuminate button 2 seconds.

To turn off back light, press and hold down the SET and 4 button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and

¢button until SEND indicator blinks twice. Initial is back light ON.

Importants:

•Some codes may be not match your equipment.

In this case, you can use LEARN mode to store these codes.

•The preset codes do not cover full functions.

If you need extra function, use LEARN mode to store extra function.

•When the batteries are getting weak, the preset procedure is not successful.

PROGRAMMING WITH THE 4-DIGIT CODE

1. Press and hold down the SOURCE button (ex TV) for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light ﬂushes.

2. Press the 4-digit code by numeric keys for appliance (code table at the end of this book) When the procedure is successful, the SEND indicator will blink twice.

Note:

If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

4. Stop when the appliance turns off.

5. Press ENTER button once to lock in the code.

CHECKING THE CODE

2. 4.

1. 1.

1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light ﬂushes.

2. Press the INFO button.

The SEND indicator will blink twice.

3. To view the code for ﬁrst digit, press 1 once.

Count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number.

Note:

If a code digit is “0”, the SEND indicator will not blink.

4. Repeat step 3 three more times for remaining

digits. Use 2 for the second digit, 3 for the third

RESETTING THE CODE

1. 1. 2.

1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice.

Then back light ﬂushes.

2. Press the below codes to reset.

TV : 1000

DVD : 2000

CD : 3000

DSS : 4000

The indicator will blink twice.

Note:

After this procedure, the selected SOURCE button is set initial code.

ENGLISH

PRESET MODE

(When operating non-Marantz AV equipment products)

This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, DVD, CD and DSS.

SCANNING THE CODE TABLE

3.	5.

digit, and 4 for the fourth digit.

Settings can be made in one of two ways.

When the preset codes are set, the following codes are contained in the source button of the remote controller.

See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.

Remote control	Corresponding preset	Device name
source name	code
TV	TV	Television
DVD	DVD	DVD player
CD	CD	CD player
DSS	SATELLITE	Satellite broadcasting
		tuner equipment

1. Switch on the appliance which should be controlled.

2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light ﬂushes.

3. Aim the remote controller at the appliance and alternately press the CH+ and SOURCE ON buttons slowly.