Marantz PD5010D manual To avoid damage and prolong operating life

Page 3

NOTE:

When you connect a computer to this monitor, attach the supplied ferrite cores. If you do not do this, this monitor will not comform to mandatory FCC standards. Attaching the ferrite cores:

Set the ferrite cores on both ends of the DVI cable (not supplied), and one end of the power cable (supplied). Close the lid tightly until the clamps click.

Use the band to secure the ferrite core (supplied).

DVI cable (not supplied)

 

 

 

 

 

 

 

 

band

band

Connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

core (small)

core

(small)

Power cable (supplied)

core (large)

band

Set side

 

(Plasma Monitor side)

To avoid damage and prolong operating life:

1.Use only with 120V 50/60Hz AC power supply. Continued operation at line voltages greater than 120 Volts AC will shorten the life of the unit, and might even cause a fire hazard.

2.Handle the unit carefully when installing it and do not drop.

3.Set the unit away from heat, excessive dust, and direct sunlight.

4.Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the unit and have it serviced by an authorized Marantz Service Center.

5.Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

6.For correct installation and mounting it is strongly recommended to use a trained,authorized Marantz dealer.

7.As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel.

Recommendations to avoid or minimize phosphor burn-in

Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged period of time, can result in phosphor burn if proper precautions are not taken. To protect your investment in this Marantz plasma monitor, please adhere to the following guidelines and recommendations for minimizing the occurrence of image burn:

*Always enable and use your computer’s screen saver function during use with a computer input source.

*Display a moving image whenever possible.

*Change the position of the menu display from time to time.

*Always power down the monitor when you are finished using it.

If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of phosphor burn:

*Lower the Brightness and Contrast levels as much as possible without impairing image readability.

*Display an image with many colors and color gradations (i.e. photographic or photo-realistic images).

*Create image content with minimal contrast between light and dark areas, for example white characters on black backgrounds. Use complementary or pastel color whenever possible.

*Avoid displaying images with few colors and distinct, sharply defined borders between colors.

Contact Marantz Service Center at 1-800-270-4533 for other recommended procedures that will best suit your particular application needs.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Model PD5010D User Guide Important Information PrecautionsTo avoid damage and prolong operating life Avertissement PrécautionsDOC avis de conformation Mises en garde et précautions de sécuritéRemarque Medinah Road Roselle, IL Tel -307-3100 Fax Limited Warranty for the Marantz Slim Series Plasma MonitorContents Ventilation Requirements for enclosure mounting How to Attach Options to the Plasma MonitorOptions Features you’ll enjoy includeContents of the Package IntroductionFront View Part Names and FunctionRGB2/ DVD2/ HD2 Rear View/ Terminal BoardRGB/PC Remote Control Unit5MULTI Battery Installation and ReplacementHandling the remote control unit Operating RangeApprox 7m/ 23ft Personal computer with a digital RGB output InstallationConnections with Equipment that has a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerRight Left External Speaker ConnectionsRGB Pin Assignments and Signal Levels for 15 pin RGB AnalogBasic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWatching with a wide screen manual When watching videos or digital video discsWhen watching high definition video source Wide OperationsWatching computer images with a wide screen When Picture Size is set to OFF Supported resolution  Picture Size settingShowing a couple of pictures on the screen at the same time Selecting the input signals to be displayedAdjusting the OSM controls Multi Screen OperationsMenu Operations OSMOn Screen Menu ControlsMain menu Sub menu Functions  Adjusting the computer image Picture Settings MenuAdjusting the picture  Picture adjustment screen Types of picture modes Example Setting the Theater mode Setting the color temperature Setting the color temperatureExample Setting Once the setting is completed Adjusting the white balance Example Adjusting the White Balance Types of noise reduction Example Setting NR-3Reducing noise in the picture  NR Sound settings menu Sound Settings MenuAdjusting the treble, bass and left/right balance Example Adjusting the bassWhen Auto Picture is OFF Screen Settings MenuAdjusting the Position,Size,Fine Picture,Picture Adj Example Adjusting the vertical position in the normal modeSetting the on-screen display Function Settings MenuAdjusting the position of the menu display Adjusting the position of the menu displayExample Adjusting the position of the menu display To adjust the positionPower management settings Setting the power management for computer imagesExample Turning the power management function on Power management functionDescription Turning the picture back on POWER/STANDBY indicatorGray Level Setting the picture to suit the movieSetting the gray level for the sides of the screen Cinema ModeReducing burn-in of the screen Setting RGB3 ADJWhen you adjust the RGB3 ADJ Example Setting PLE to LockInverse Resetting to the default valuesPLE OrbiterAudio Input Option Settings MenuSetting the allocation of the audio connectors Setting the BNC connectorsBNC Select Setting a computer image to the correct RGB select screenExample Setting the RGB Select mode to Motion To set the RGB select mode to MotionHD Select modes Setting high definition images to the suitable screen sizeExample Setting the 1080B mode to RGB Select modesPicture Size Setting the picture size for RGB input signalsExample Setting the on mode to OFF Information MenuLanguage settings Setting the language for the menusSetting the video signal format Example Setting the menu display to DeutschNtsc Video signal formatsConnections Type of connector D-Sub 9-pin maleExternal Control ApplicationUnit ID 1 and Unit ID CommandCheck Sum CKS, Error Processing, and ACK Communication FormatCommand Reference List Color Gain Data Audio Mute OnAudio Mute Off OSM SelectBright Gain Data Input Mode RequestSharpness Gain Data Contrast Gain DataRED Gain Data Green Gain DataBlue Gain Data Video ADJ Request Long Life Set Failure Mode RequestAudio Select Set Audio Select RequestTable of Signals Supported Supported resolutionComputer input signals supported by this system Page Symptom Checks Remedy TroubleshootingSignals SpecificationsAustria Is a registered trademark
Top Page Image Contents