RCA L26HD31S warranty Programming the Remote, Using Direct Entry, Using a Manual Code Search

Page 24

Programming the Remote

The CANCEL button is used as visual feedback during the programming operation. During programming, the CANCEL button illuminates when buttons are pressed and turns off when buttons are released. When programming is finished, the CANCEL button blinks slowly to indicate success and blinks rapidly to indicate failure.

Note: All component buttons are inoperable during Programming Mode.

There are three ways to program the remote control to operate other components: Direct Entry, Manual Code Search, and Automatic Code Search. You must try Direct Entry for at least one code before trying the other methods.

Using Direct Entry

1.Turn on the component you want to control.

2.On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons (approximately

3 seconds) until the CANCEL button illuminates. Release the buttons.

3.Press and release the component button.

4.Enter the appropriate four-digit code for the component you want to operate. The first digit indicates the component type (0 for DVD, 1 for Satellite TV, 2 for Cable, 3 for DVR, 4 for VCR, 5 for Audio, 6 for CD); the other three digits indicate the brand and model. Look up the brand and codes for the component in the list at the end of this section. Codes are listed by component type and are arranged alphabetically.

5.The CANCEL button blinks slowly to indicate success. Repeat these steps until you’ve tested all codes for your component’s brand, or try to run a Manual Code Search.

Using a Manual Code Search

Note: Before using Manual Code Search, use Direct Entry. This lets the remote know which type of component you are programming. Then proceed with the following steps:

1.Turn on the component you want to control.

2.On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons (approximately

3 seconds) until the CANCEL button illuminates. Release the buttons.

3.Press and release the component button.

4.Repeatedly press and release the left arrow or right arrow, watching for the component to respond. If the component turns off, press and release the OK button to save the code. The CANCEL button blinks slowly to indicate success.

5.When all codes have been searched, the CANCEL button blinks rapidly to indicate failure, and the remote returns to normal operation.

Note: Use the right arrow to search ahead; use the left arrow to search back. Press the ON•OFF button to switch to Automatic Code Search Mode.

24

Chapter 2 Using the Remote Control

Page 23 Page 25
Image 24
Page 23 Page 25
Contents User’s guide Important Information Important Safety Instructions Table of Contents Using the Remote Control Other Information Before Initial Setup Attaching Your TV to the Table Stand Fixed Table Stand Assembly for Model L32HD31 Parts List Step Swivel Table Stand Assembly for Models L32HD36 and L40HD36 TV is ready for placement Connections and Setup Chapter Obtain the Signal Mounting Your TV to the WallChoose Your Connections Customer SupportConnecting a Component with Composite Video Good Connecting a Component with Component Video BetterComposite Video Connection Component Video ConnectionConnecting a Component with Hdmi Best HDMI/DVI Connection BestConnecting a PC Component PC ConnectionViewing the Picture from the Connected Component Viewing a PCUsing the Remote Control to Complete Initial Setup Plug in the TVPut Batteries in the Remote Turn on the TVComplete the Initial Setup Set the TV Location ModeComplete Channel Setup Set the Signal TypeWhat To Expect Watching TVChanging Channels Explanation of Jacks in alphabetical order Buttons and Other Jacks on Your TV/DVD Side Input JacksSide Panel Buttons Remote Control Buttons TV FunctionsProgramming the Remote to Operate Other Components Input ButtonDetermine If You Need to Program Remote Using Direct Entry Using a Manual Code SearchProgramming the Remote Using Automatic Code Search Using the RemoteManual Reset Modes of OperationRemote Code list CD Codes DVD/VCR Combo Codes 016 047 Autotuning Channel BannerParental Controls and V-Chip Chip US and CanadaLock/Unlock Parental Controls Chip Rating ScreenUS V-Chip TV Ratings Blocking Specific Content Themes US V-Chip Movie Rating LimitReset Downloadable Data Blocking Canada V-Chip RatingsFuture Rating Region Blocking Unrated/Exempt ProgramsAdditional Features Screen FormatsTo change the screen formats Using the Menu System Picture SettingsPicture Menu Sound Menu Setup Menu Channel MenuParental Control Menu Closed CaptionTime Menu Frequently Asked Questions FAQs Troubleshooting TV Problems TV won’t turn onThere is no picture and no sound but the TV is on Sound is fine, but the picture is poor qualityScreen is blank Buttons on the side panel don’t workTV turns off unexpectedly You can’t select a certain channelYou are having problems with the Hdmi Connection Remote control doesn’t workYou are experiencing problems with V-Chip/Parental Controls Don’t remember my password and I want to unlock the TVChip Rating Explanations US V-Chip Rating SystemCanadian English V-Chip Rating System Canadian French V-Chip Rating System TTE Technology, Inc. TTE Limited Warranty All LCD ModelsWhat your warranty does not cover Product Registration Limitation of WarrantyHow State Law relates to this warranty Limited Warranty For how long after purchaseIf you purchased your unit outside of Canada Care and Cleaning Page FCC Information
Top Page Image Contents