RCA D44LPW134 manual Other Information

Page 59

Other Information

9.Loosen the two screws on the lamp unit inside the TV (the screws stay with the unit so just loosen them, don’t remove them).

Step 9

10.As you remove the lamp, pay attention to how the lamp ﬁts so that you can use the proper orientation when you’re installing the new lamp. To remove the lamp unit:

•grasp the handles and pull straight back to remove the entire lamp assembly unit from the TV.

•place the old unit out of the way where it won’t get broken or dropped.

Step 10

11.Remove the new lamp assembly unit from its packaging.

12.Make sure the lamp unit is oriented in the correct position, and gently slide it into the lamp access opening as far as it can go (it ﬁts snugly).

13.Tighten the two screws on the new lamp unit.

14.Put the old lamp unit into the box in which the new lamp unit was packaged.

15.Replace the lamp access door (the TV won’t turn on unless this door is in place and properly attached).

a.Insert the catch tabs (also called latches) into the slots on the left side of the lamp access compartment ﬁrst. Then put the rest of the door in place by rotating the door until it is fully closed and the latches are engaged.

b.Tighten the screw.

16.Plug the power cord into the back of the TV ﬁrst and then back into the wall outlet strip.

17. Turn on the TV.

18.After the TV warms up (up to 60 seconds), you should see a picture. If you don’t see a picture, check the following:

•Make sure TV is plugged in.

•Make sure you’ve tuned the TV to a valid channel.

•Try turning on the TV both ways: with the remote control, and then with the power button on the front of the TV.

•Make sure the lamp unit access door is properly and completely closed.

•Make sure the screws are completely tightened.

•Unplug the power cord from the TV and from the power outlet. Return to step 7 and make sure the lamp unit is fully seated in the housing.

•If the TV still doesn’t come on, you need to have the unit professionally serviced. See your warranty.

Chapter 5

57

Image 59

Contents User’s Guide Product Registration Product Information Important InformationImportant Safety Instructions How DLP Works Lamp ReplacementThank you for choosing RCA Scenium Part 1 DLP- brilliance, in color, design, and technologyAspect Ratio Part 2 Why RCA Scenium DLP is betterResolution it’s math...that works for you IntroductionVirtual Dolby* Surround Pro Logic Digital Signal and SoundTruScan Digital Reality DVI-HDTV InputTable of Contents Table of Contents Chapter Overview Connections & SetupThings to Consider Before You Connect Connections & SetupCables Connection Go to Needed Title Choose Your ConnectionCables Needed to Connect Components to Your TV ComponentsBack Panel Jacks in alphabetical order Explanation of JacksFront Input Jacks VCR 1A1BGo to TV + Hdtv Tuner + VCR + DVD PlayerSatellite 3B 3AMake sure cable or antenna is connected to your VCR TV + Satellite Receiver + VCR2B 2A TV + DVD + VCR Front Panel Buttons TV+ A/V Receiver or SpeakersPut batteries in the remote How to Use the Remote Control toComplete the Initial Setup Plug in the TVChanging Lists and Labels Welcome Screen and Connection ConﬁrmationComplete Auto Channel Search Using the Remote Control Buttons on the Remote Control Using the Remote ControlTip Programming the Remote Using Direct EntryProgramming the Remote to Operate Other Components Find Out If You Need to Program the RemoteUsing Automatic Code Search How to Use the Remote After You’ve Programmed ItAdding a Learned Function Learning FeatureUsing the Remote Control Deleting ALL Learned Functions Clearing a Learned FunctionVolume Punchthrough Deleting All Punchthrough Commands Using the Input ButtonDVD codes Audio CodesHdtv Tuner Codes Cable Box CodesProgrammable for VCR and AUX/HD buttons VCR CodesChannel Banner Autotuning Parental Controls and V-Chip Using the TVs FeaturesChannel Banner Using the TV’s FeaturesAutotuning Why You Should Use the Autotuning FeatureHow to Set Up the Autotuning Feature US V-Chip TV Rating Limit Parental Controls and V-ChipHow V-Chip Works for USA and Canada V-Chip Rating Screen USA Description and Content Themes for Age-Based RatingsViewing Age-Based Ratings Blocking Speciﬁc Content ThemesContent Themes Blocking Age-Based RatingsCanada V-Chip Ratings Canadian French V-Chip Rating System Blocking Canadian V-Chip RatingsFront Panel Block Chip Movie Rating LimitBlocking Unrated/Exempt Programs Lock/Unlock Parental ControlsPIP and POP Buttons PIP Picture-in-Picture and POPPicture-outside-Picture Operation Using the TVs Menu System Sound Menu Using the TV’s Menu SystemUsing the TV’s Menu System Picture Menu Advanced picture settingsDisplay options settings Parental Control Menu Channel Guide MenuTime Menu PIP Menu Setup MenuPreferences Other Information Other Information TroubleshootingNo picture, sound okay TV turns on unexpectedlyBlank screen No sound, picture okayDon’t remember my password and I want to unlock the TV Volume buttons not adjusting volume louderLow battery warning appears on screen TV picture keeps switching between screen formats abruptlyReplacing the Lamp Unit Lamp Replacement InstructionsSteps 7 StepOther Information What your warranty covers Limitation of Warranty HOW to Order Accessory InformationDVD IndexTocom 1642954A TTE Technology, IncNorth Meridian Street Indianapolis,