Attaching the pedestal to TV

■Assembling the pedestal

Insert the protrusion of the Neck into the Base firmly.

Neck

Protrusion of the

Neck (bottom)

Turn the stand over and fix stand neck securely with assembly screws.

(for 42”/50”: 3 screws, for 55”/60”: 4 screws)

•Do not hold the neck when turning over the stand. B x 3 pcs. (for 42”/50”)

B x 4 pcs. (for 55”/60”)

[TC-P42UT50, TC-P50UT50]

Accessories

Assembly screws

XYN4+F10FNK (Black) size (M4 x 10)

(for 42”/ 50” (5), for 55”/60” (1))

		Front	Hole for
		Front	screw
			screw
	Front
		Back of Stand
			[TC-P55UT50,
			TC-P60UT50]
Attach the Bracket to the protrusion of Neck.		Attach the cover and fix securely with
Make sure that the bracket is anchored		assembly screw.
before fixing the screws.			A x 1 pcs.
Fix securely with assembly screws. (4 screws)			A x 1 pcs.
Protrusion of Neck (top)	B x 4 pcs.		Cover

Bracket

XYN5+F16FN (silver)

size (M5 x 16)

(for 42”/ 50” (7), for 55”/60” (12))

Bracket (1)

TBL5ZA3238 (for 42”/50”)

TBL5ZA3200 (for 55”/60”)

Neck (1)

TXFBL5Z0069 (for 42”/50”)

TXFBL5Z0085 (for 55”/60”)

Cover (1)

TXFBL5Z0071 (for 42”/50”)

TXFBL5Z0056 (for 55”/60”)

■Set-up

	Tighten assembly screws (for 42”/50”) / (for 55”/60”) (total 4 screws)	Cover is in the same bag
		with Owner’s Manual
	loosely at first, then tighten them firmly to fix securely.
		Base (1)

		TBL5ZX0292 (for 42”)
		TBL5ZX0294 (for 50”)
		TBL5ZX0420 (for 55”)
Rear side		TBL5ZX0421 (for 60”)
Rear side
Arrow	Removing the pedestal from the TV
mark	Removing the pedestal from the TV
Hole for pedestal	Be sure to remove the pedestal in the following way when using
installation	the wall-hanging bracket or repacking the TV.
A x 4 pcs. (for 42”/50”)	Remove the assembly screws	(for 42”/50”) /	(for 55”/60”)
A x 4 pcs. (for 42”/50”)	from the TV.
B x 4 pcs. (for 55”/60”)	from the TV.
B x 4 pcs. (for 55”/60”)	Lift the TV from the pedestal.
Bracket	Remove the assembly screw	from the cover.
Base	Pull out the cover.

(Image)	Work on a flat surface	Remove the assembly screws	from the Bracket.
		Remove the assembly screws	from the Back of stand and

Warning

pull out the neck.

Do not disassemble or modify the pedestal.

Otherwise, the TV may fall over and become damaged, and personal injury may result.

Caution

Do not use any pedestal other than that provided with this TV.

Otherwise, the TV may fall over and become damaged, and personal injury may result.

Do not use the pedestal if it becomes warped or physically damaged.

If you use the pedestal when it is physically damaged, personal injury may result. Contact your nearest Panasonic Dealer immediately.

During set-up, make sure that all screws are securely tightened.

If sufficient care is not taken to ensure screws are properly tightened during assembly, the pedestal will not be strong enough to support the TV, and it might fall over and become damaged, and personal injury may result.

When removing the pedestal, do not remove the pedestal by any methods other than the specified procedure. (Above)

Otherwise, the TV and/or pedestal may fall over and become damaged, and personal injury may result.	9