Panasonic TQB2AA0547 PC Input Terminals connection, Signal Names for Mini D-sub 15P Connector

Page 9

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

(Female)

Mini D-sub 15p

RGB

PC cable

(Male)

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 768 × 768 dots (TH-42PD12U), 1,024 × 768 dots (TH-50PD12U) when the aspect mode is set to “4:3”, and 1,024 × 768 dots (TH-42PD12U), 1,366 × 768 dots (TH-50PD12U) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

•Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

•Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection).

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10

9

 

8

7

6

15

14

 

13

12

 

11

Pin Layout for PC Input Terminal

Pin No.

Signal Name

Pin No.

Signal Name

Pin No.

Signal Name

1

R (PR/CR)

6

GND (Ground)

11

NC (not connected)

2

G (Y)

7

GND (Ground)

12

SDA

3

B (PB/CB)

8

GND (Ground)

13

HD/SYNC

4

NC (not connected)

9

+5 V DC

14

VD

5

GND (Ground)

10

GND (Ground)

15

SCL

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operating Instructions Manual de instrucciones TH-42PD12U TH-50PD12URisk of Electric Shock Do not Open Important Safety Instructions Trademark Credits FCC StatementWhen using the Plasma Display Safety PrecautionsSetup MaintenanceAC Power Supply Cord If problems occur during useAccessories Accessories SuppliedRemote Control Batteries Cable fixing band ConnectionsPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorCommand Signal names for D-sub 9P connectorSerial Terminals connection Communication parametersAV connection RCA-BNCVCR Power on / OFF Connecting the AC cord plug to the Plasma DisplayConnecting the plug to the Wall Outlet OSD Language Display Orientation When first switching on the unitVideo S-VIDEO Component PC Selecting the input signalMain Power On / Off Switch Power Indicator Remote control sensor Volume AdjustmentInput button Input signal selection Basic ControlsAction button OFF Timer buttonAspect button Standby on / OFF buttonOn-Screen Menu Displays Screen size SpecificationsFor the U.S.A and Puerto Rico Panasonic Professional Flat Panel Display Limited WarrantyFor Canada Limited Warranty StatementPage Page Page Panasonic Professional Display Company Customer’s RecordExecutive Office Panasonic Canada Inc
Top Page Image Contents