Panasonic TC-P54Z1 operating instructions AttachingAttachinge pedestalthe pedestalto TV to TV

Page 10
Back of Display Unit
Assembly screws

Accessories/Optional Accessory

AttachingAttachinge pedestalthe pedestalto TV (continued)to TV

Warning

Do not disassemble or modify the pedestal.

Otherwise the TV may fall over and become damaged, and personal injury may result.

Caution

Do not use any other TV and displays.

Otherwise the TV may fall over and become damaged, and personal injury may result.

Do not use the pedestal if it becomes warped or physically damaged.

If you use the pedestal when it is physically damaged, personal injury may result. Contact your nearest Panasonic Dealer immediately.

During set-up, make sure that all screws are securely tightened.

If sufficient care is not taken to ensure screws are properly tightened during assembly, the pedestal will not be strong enough to support the TV, and it might fall over and become damaged, and personal injury may result.

Attaching the Speaker to TV

Fix the Mounting bracket securely to the back of the Display unit with Assembly screws .

Insert the speaker mounting screws temporarily in the screw outermost holes of the speaker and fix the speaker mounting screws to the speaker mounting bracket.

Orient the front side of the Mounting bracket toward the rear side of the speaker and Display Unit side.

Fix it same as the speaker at the other side.

There will be a gap between the Display Unit and the speaker.

Accessories

Speaker (2)

SP-54Z1U

Mounting bracket

Back of

Display Unit

Mounting bracket

[Top]

Mounting Assembly

bracket screws [Lower right]

Place the temporarily inserted screws into the counter sunk holes

on the bracket

Speaker

[Top] (2)

TXFKR04DLUJ

Front Back

[Lower right] (1)

TXFKR05DLUJ

Front Back

[Lower left] (1)

TXFKR06DLUJ

Front Back

Connect Display Unit and speaker with speaker cable.

Fix it in the same way as the speaker on the other side.

Speaker

Lower right

Assembly screws

 

 

(Back of Display Unit)

TXFXY01DLUJB

 

 

 

(8)

(8)

 

Speaker

Speaker cable (2)

 

 

TXJ/SPDKUU-1

 

To open the Clamper

cable

 

Connect the terminal

 

Hook

Press the part and

near the ferrite core to

 

 

remove the hook.

the Display Unit.

 

Note

Tighten the screws firmly.

Insert to the end of the speaker cable terminal firmly.

Loosen the screw shown in fig. A above to adjust the gap between the speaker and the Display Unit. Do not hold the speaker to transport the unit.

10

Image 10
Contents Model No. TC-P54Z1 ViVAViera Turn your own living room into a movie theater Viera Cast is a trademark Sdhc Logo is a trademarkContents Set up Safety PrecautionsImportant Safety Instructions Plasma TV may fall or tip overIf Problems Occur During Use AC Power Supply CordHandling the power supply cord When Moving the Plasma TVViera Consumerproducts@panasonic.comDo not display a still picture for a long time Typical still imagesOptional Accessory Accessories/Optional AccessoryAccessories AccessoriesSet-up QuickGuideStart Accessories/Optional AccessoryAssembling the pedestal Attaching the pedestal to TVDo not disassemble or modify the pedestal AttachingAttachinge pedestalthe pedestalto TV to TVAttaching the Speaker to TV Do not use any other TV and displaysConnecting Display Unit, Tuner Box and Wireless Unit Wired connectionWireless connection Display UnitExclusive cable for Wireless Transmitter Cable Binding for Wireless UnitConnect Wireless Unit Transmitter to Tuner Box Hole for Cable clamper Ferrite coreInstallation Environment Installing the Display Unit, Tuner Box and Wireless UnitPrecautions for Wireless Unit Transmission RangeTo attach Antenna terminal Pin terminals Hdmi terminalCable Binding Instructions To bundleVHF/UHF Antenna Connecting Antenna To watch TVBasic Connection Cable Box/CableAV Equipment DVD Recorder Connecting DVD recorder VCR To record/playbackConnecting TV and AV equipment Or VCRReceiver Connecting TV and AV equipment Please refer to a D on pSatellite To use S Video terminals To use Hdmi terminalsTo use Component terminals To use Composite terminalsIdentifying Controls Basic Connection AV cable TV controls/indicatorsIdentifying Controls ConnectionsRemote control First Time Setup Identifying Controls Turn the TV On with the Power button Display UnitTuner Box power will be also turned on Select your viewing environment First Time SetupAuto channel setup Be sure to select Home UseSelect Auto program Network settingViera Cast setting Start scanning the channelsAuto setting Adjust the clockManual setting Set the Input labelsWatching TV Turn power onWatching TV First Time Setup Select a channel numberRecall Favorite FeatureInformation Change aspect ratio Call up Favorite channelStart Network Camera viewing p Using Viera ToolsDisplay Viera Tools Select the item NextInsert the SD card Set SD card setting and select Play SD card nowViewing from an SD Card Select the movie to be listedChange SettingsMovie AudioMenu screen Press to return to the previous screen Photo viewerPress to exit from To display/hide Navigation areaSort Adjust the picture Display Photo settingsSlideshow settings PhotoWatching Videos and DVDs Display the Input select menu Select the input modeTo return to TV Press Game to switch to the game screen Input SelectSelect Viera Link Display menu Select SetupSelect Viera Link settings Select OnSelect the item and press OK Other settingsDisplay the Home screen Operate Viera CastSelect wired or wireless connection Contact your Broadband service providerConnecting to the Internet Basic operation for Network camera Network CameraStart up Network camera Select Network Camera in Viera LinkCamera SettingNetwork Network CameraDisplay the Input select menu Corresponding signalsDisplaying PC Screen on TV Select PCAdjustments PC menu setting change as desiredMenu Adjustments/Configurations options Displaying PC Screen on TVDisplay menu How to Use Menu FunctionsAdjust or select Select the menuAdjustments/Configurations alternatives How to Use Menu Functions picture, sound quality, etcAV mode, the Audio menu and Setup menu give fewer options Press to exit from How to Use Menu FunctionsDisplay Sub Menu Menu screenSets Power off link of Hdmi connection equipment p Yes/No Adjusts the clock pSets the time for Pixel orbiter-Periodic setting /2/3/4 Set Auto power stand-by of Hdmi connection equipment. pViera LinkTM Hdavi ControlTM Hdmi cableViera LinkTM Connections Setting of this unit after connectionViera LinkTM Hdavi ControlTM Back of the TV Digital Audio out Or or Hdmi cableSet Select settingsAuto power save for For Hdavi Control 3 or laterTransmittable data Recorder Home theater Player For RecorderDisplay Viera Link menu SelectSelect Speaker output Select Home theater or TV Available TV’s remote control buttonsControlTM Select Viera Link controlNetwork Setting Select Network settingSelect Connection test and press OK SettingSelect IP setting mode and set to Automatic Each IP address is acquired automaticallySelect the item and adjust Viera Casttm SettingSelect Viera Cast setting ScreenTM Setting Proxy portLock Input your 4-digit passwordSelect the Lock mode Display menu Select LockGame lock Change passwordChannel lock Program lockCheck signal strength Editing and Setting ChannelsSelect ANT/Cable setup Set automaticallyEditing and Setting Channels Display menu Select Closed caption Closed CaptionDisplay Closed caption Input Labels Closed Caption Input LabelsSelect Input labels Display labels of connected devicesSelect the timer to set Using TimerDisplay menu Select Timer Set the timerControl registration Using Timer Remote control registrationDisplay Remote control registration Select YesRecommended AV Connections Camcorder VCR DVD PlayerRatings List for Lock Ratings List for Lock Recommended AV ConnectionsClosed caption CC Technical InformationAspect Ratio Format Message Technical InformationData format for SD Card browsing SD Card warning messages MeaningViera LinkTM Hdavi ControlTM Picture modePro setting Hdmi connectionSize Technical Information FAQs, etcInput signal that can be displayed Side barsCare and Cleaning Specifications Specifications Technical Information Care and CleaningRecording does not start immediately White spots or shadow images noiseInterference or frozen digital channels intermittent sound This case, usage of the Panasonic SC-ZT1 is recommendedChaotic image, noisy No image can be displayed Frequently Asked Questions FAQs, etcPress any button to return moves on the screen Black Box appears No sound is produced Sound is unusualOn-Site or Carry-in Service Limited Warranty CoverageLimited Warranty Limits And Exclusions Accessory Purchases United States and Puerto Rico Customer Services Directory United States and Puerto RicoNpcparts@us.panasonic.com Quick Start Guide Limited Warranty for Canada Panasonic Product Limited WarrantyLimited Warranty for Canada Customer’s Record