Panasonic TH-42PR10U, TH-37PR10U Serial Terminals connection, Communication parameters, Command

Page 11

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

COMPUTER	1	2	3	4	5

		6	7	8	9
RS-232C Straight cable	SERIAL
	Pin layout for SERIAL Terminal

D-sub 9p

Notes:

•Use the RS-232C cable to connect the computer to the Plasma Display.

•The computer shown is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal.

The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level	RS-232C compliant
Synchronization method	Asynchronous
Baud rate	9600 bps
Parity	None
Character length	8 bits
Stop bit	1 bit
Flow control	-

RS-232C Conversion cable

D-sub 9-pin female		Details
	2	R X D
	3	T X D
4	5	GND
4	• 6	Non use
	7	Shorted
	8	Shorted
	8
1	• 9	NC

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX

	Colon	Parameter(s)	End
Start	3-character	(1 - 5 bytes)	(03h)
(02h)	command (3 bytes)

Notes:

•If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command.

•If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

•SL1A, SL1B, SL2A and SL2B of Command IMS are available only when a dual input terminal board is attached.

Command

	Command	Parameter	Control details
	PON	None	Power ON
	POF	None	Power OFF
	AVL	**	Volume 00 - 63
	AMT	0	Audio MUTE OFF
	AMT	1	Audio MUTE ON
		1	Audio MUTE ON
	IMS	None	Input select (toggle)
		SL1	Slot1 input
		SL2	Slot2 input
		SL3	Slot3 input
		PC1	PC input
		SL1A	Slot1 input (INPUT1A)
		SL1B	Slot1 input (INPUT1B)
		SL2A	Slot2 input (INPUT2A)
		SL2B	Slot2 input (INPUT2B)
	DAM	None	Screen mode select (toggle)
		NORM	NORMAL (4 : 3)
		ZOOM	ZOOM
		FULL	FULL
		JUST	JUST
		SELF	Panasonic AUTO

With the power off, this display responds to PON command only.

11

Image 11

Contents Illustration shown is an image Operating Instructions Manual de instruccionesEnglish Español Model No. Número de modeloRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionCanadian Notice When using the Plasma Display Safety PrecautionsIf problems occur during use MaintenanceSetup AC Power Supply CordCheck that you have the Accessories and items shown AccessoriesAccessories Supplied AC cord fixing ConnectionsPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorBasic format for control data CommandSerial Terminals connection Communication parametersConnecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display INPUT1 INPUT2 INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageOn OFF Basic ControlsDigital Zoom see Press to access Channel AdjustmentVolume Adjustment OFF Timer buttonOn-Screen Menu Displays Advanced SettingsPicture Setup Sound On Time / Power OFF Time / Power OFF TimeNormal Full Aspect ControlsNormal Zoom Full Is pressed During Multi PIP OperationsRGB/PC in mode Adjusting POS. /SIZEClock Phase Clock PhaseMulti PIP 1366x768@60Hz RGB, DVI, Hdmi Advanced PIPOne screen Advanced PIP Press to exit from Options menu Sub screen Main screenCinema Picture AdjustmentsStandard DynamicAdvanced Settings Mute Sound AdjustmentSelect the magnification required for the enlarged display Digital ZoomDisplay the operation guide PositionButton Forward Present Time SetupPresent Time Setup Press to set up DAY or Present Time of DAYPower on Time / Power OFF Time SET UP TimerDisplay the SET UP Timer Screen Press to select Negative / Scroll selection Mode selectionStart setting Screensaver For preventing image retentionReduces screen image retention Setup of Screensaver TimePress to exit from Screensaver Side BAR AdjustOFF Dark MID Bright Addition sign Selected Input Reduces power consumptionCustomizing the Input labels Component RGB SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesColor System Color System / Panasonic AutoPulldown / Video NR FREQ. kHz / V-FREQ. Hz Setting RGB sync signalSync Refresh RateOptions Adjustments Off MENU&ENTER On Off Initial VOL Sets normal volume LevelVolume display can go up to 63 regardless of the settings Becomes the same as the Maximum VOL levelNormal Standby EnableInitial Power FunctionRotate Off Does not rotate the image State regardless of the slot power setting InstallationNormalization Weekly Command Timer Press to set each item Press to select a command numberPress to select Time / Command Time Set the time to execute a command programPress to select YES Shipping conditionPlasma Display panel TroubleshootingSymptoms Checks Symptoms CheckRGB PC input signalsCommand list of Weekly Command Timer Specifications Register Your Product Ambler Drive, Mississauga, Ontario L4W 2T3 Panasonic Canada Inc Broadcast & Television Systems DivisionCustomer’s Record